Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 60384-8:2005 Fixed capacitors for use in electronic equipment - Sectional specification: Fixed capacitors of ceramic dielectric, Class 1, 2010
- 60384-8e-mono-ed3 WORDTEXT.pdf [Go to Page]
- 1 General [Go to Page]
- 1.1 Scope
- 1.2 Object
- 1.3 Normative references
- 1.4 Information to be given in a detail specification [Go to Page]
- 1.4.1 Outline drawing and dimensions
- 1.4.2 Mounting
- 1.4.3 Ratings and characteristics [Go to Page]
- 1.4.3.1 Rated capacitance range
- 1.4.3.2 Particular characteristics
- 1.4.3.3 Soldering
- 1.4.4 Marking
- 1.5 Terms and definitions
- 1.6 Marking [Go to Page]
- 1.6.1 The information given in the marking is normally selected from the following list; the relative importance of each item is indicated by its position in the list:
- 2 Preferred ratings and characteristics [Go to Page]
- 2.1 Preferred characteristics [Go to Page]
- 2.1.1 Preferred climatic categories
- 2.2 Preferred values of ratings [Go to Page]
- 2.2.1 Rated temperature
- 2.2.2 Rated voltage (UR)
- 2.2.3 Category voltage (UC)
- 2.2.4 Preferred values of rated capacitance and associated tolerance values [Go to Page]
- 2.2.4.1 Preferred values of rated capacitance
- 2.2.4.2 Preferred tolerances on rated capacitance
- 2.2.5 Temperature coefficient (α)
- 3 Quality assessment procedures [Go to Page]
- 3.1 Primary stage of manufacture
- 3.2 Structurally similar components
- 3.3 Certified records of released lots
- 3.4 Qualification approval [Go to Page]
- 3.4.1 Qualification approval on the basis of the fixed sample size procedure
- 3.4.2 Tests
- 3.5 Quality conformance inspection [Go to Page]
- 3.5.1 Formation of inspection lots
- 3.5.2 Test schedule
- 3.5.3 Delayed delivery
- 3.5.4 Assessment levels
- 4 Test and measurement procedures [Go to Page]
- 4.1 Visual examination and check of dimensions
- 4.2 Electrical tests [Go to Page]
- 4.2.1 Capacitance [Go to Page]
- 4.2.1.1 Measuring conditions
- 4.2.1.2 Requirements
- 4.2.2 Tangent of loss angle (tan δ) [Go to Page]
- 4.2.2.1 Measuring conditions: same as in 4.2.1
- 4.2.2.2 Requirements
- 4.2.3 Insulation resistance (Ri) [Go to Page]
- 4.2.3.1 Measuring conditions
- 4.2.3.2 Requirements
- 4.2.4 Voltage proof [Go to Page]
- 4.2.4.1 Test conditions
- 4.3 Temperature coefficient (α) and temperature cyclic drift of capacitance [Go to Page]
- 4.3.1 Preliminary drying
- 4.3.2 Measuring conditions
- 4.3.3 Requirements
- 4.4 Robustness of terminations
- 4.5 Resistance to soldering heat [Go to Page]
- 4.5.1 Initial measurement
- 4.5.2 Conditions
- 4.5.3 Final inspection, measurements and requirements
- 4.6 Solderability [Go to Page]
- 4.6.1 Conditions: No preliminary drying.
- 4.7 Rapid change of temperature (if required in the detail specification) [Go to Page]
- 4.7.1 Initial measurement
- 4.7.2 Number of cycles: 5
- 4.7.3 Recovery: 24 h ± 2 h.
- 4.8 Vibration [Go to Page]
- 4.8.1 The following degree of severity of test Fc applies
- 4.8.2 Final inspection, measurements and requirements
- 4.9 Bump [Go to Page]
- 4.9.1 Initial measurements
- 4.9.2 The detail specification shall state which of the following preferred severities applies:
- 4.9.3 Final inspection, measurements and requirements
- 4.10 Shock [Go to Page]
- 4.10.1 Initial measurements
- 4.10.2 The detail specification shall state which of the preferred severities applies as stated in Table 14.
- 4.10.3 Final inspection, measurements and requirements
- 4.11 Climatic sequence [Go to Page]
- 4.11.1 Initial measurements
- 4.11.2 Dry heat
- 4.11.3 Damp heat, cyclic, Test Db, first cycle
- 4.11.4 Cold [Go to Page]
- 4.11.4.1 Final inspection and requirements
- 4.11.5 Low air pressure
- 4.11.6 Damp heat, cyclic, Test Db, remaining cycles [Go to Page]
- 4.11.6.1 Conditions of tests
- 4.11.6.2 Recovery
- 4.11.6.3 Final inspection, measurements and requirements
- 4.12 Damp heat, steady state [Go to Page]
- 4.12.1 Initial measurement
- 4.12.2 Conditions of test
- 4.12.3 Within 15 min after removal from the damp heat test, the voltage proof test according to 4.2.4 shall be carried out, but with the rated voltage applied.
- 4.12.4 Recovery
- 4.12.5 Final inspection, measurements and requirements
- 4.13 Endurance [Go to Page]
- 4.13.1 Initial measurement
- 4.13.2 Conditions of test
- 4.13.3 Recovery
- 4.13.4 Final inspection, measurements and requirements
- 4.14 Component solvent resistance
- 4.15 Solvent resistance of the marking [Go to Page]