Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 60384-9:2005 Fixed capacitors for use in electronic equipment - Sectional specification: fixed capacitors of ceramic dielectric, Class 2, 2010
- 60384-9e-mono-ed3edited.pdf [Go to Page]
- General [Go to Page]
- Scope
- Object
- Normative references
- Information to be given in a detail specification [Go to Page]
- Outline drawing and dimensions
- Mounting
- Ratings and characteristics [Go to Page]
- Rated capacitance range
- Particular characteristics
- Soldering
- Marking
- Terms and definitions
- Marking [Go to Page]
- The information given in the marking is normally selected fr
- Preferred ratings and characteristics [Go to Page]
- Preferred characteristics [Go to Page]
- Preferred climatic categories
- Preferred values of ratings [Go to Page]
- Rated temperature
- Rated voltage (UR)
- Category voltage (UC)
- Preferred values of rated capacitance and associated toleran [Go to Page]
- Preferred values of rated capacitance
- Preferred tolerances on rated capacitance
- Temperature characteristic of capacitance
- Quality assessment procedures [Go to Page]
- Primary stage of manufacture
- Structurally similar components
- Certified records of released lots
- Qualification approval [Go to Page]
- Qualification approval on the basis of the fixed sample size
- Tests
- Quality conformance inspection [Go to Page]
- Formation of inspection lots
- Test schedule
- Delayed delivery
- Assessment levels
- Test and measurement procedures [Go to Page]
- Special preconditioning
- Visual examination and check of dimensions
- Electrical tests [Go to Page]
- Capacitance [Go to Page]
- Measuring conditions
- Requirements
- Tangent of loss angle (tan δ) [Go to Page]
- Measuring conditions
- Accuracy
- Requirements
- Insulation resistance (Ri) [Go to Page]
- Measuring conditions
- Requirements
- Voltage proof [Go to Page]
- Test conditions
- The voltages in Table 9 shall be applied between the measuri
- Requirement
- Temperature characteristic of capacitance [Go to Page]
- Special preconditioning
- Measuring conditions
- Requirements
- Robustness of terminations
- Resistance to soldering heat [Go to Page]
- Special preconditioning
- Initial measurement
- Recovery: 24 h ± 2h.
- Final inspection, measurements and requirements
- Solderability [Go to Page]
- Conditions:.
- The performance requirements are given in Table 4.
- Rapid change of temperature [Go to Page]
- Special preconditioning
- Initial measurement
- Number of cycles: 5
- Recovery: 24 h ± 2 h.
- Vibration [Go to Page]
- The following degree of severity of test Fc apply:
- Final inspection, measurements and requirements
- Bump [Go to Page]
- Initial measurements
- The detail specification shall state which of the following
- Final inspection, measurements and requirements
- Shock [Go to Page]
- Initial measurements
- The detail specification shall state which of the preferred
- Final inspection, measurements and requirements
- Climatic sequence [Go to Page]
- Special preconditioning [Go to Page]
- Initial measurements
- Dry heat
- Damp heat, cyclic, Test Db, first cycle
- Cold [Go to Page]
- Final inspection and requirements
- Low air pressure [Go to Page]
- The test, if required in the detail specification, shall be
- Immediately after achieving the low pressure, UR shall be ap
- Final inspection and requirements
- Damp heat, cyclic, Test Db, remaining cycles [Go to Page]
- Conditions of test
- Recovery: 24 h ± 2 h
- Final inspection, measurements and requirements
- Damp heat, steady state [Go to Page]
- Special preconditioning
- Initial measurement
- Conditions of test
- Recovery: 24 h ± 2 h
- Final inspection, measurements and requirements
- Endurance [Go to Page]
- Special preconditioning
- Initial measurement
- Conditions of test
- Recovery: 24 h ± 2 h.
- Final inspection, measurements and requirements
- Component solvent resistance (if applicable)
- Solvent resistance of the marking (if applicable) [Go to Page]