Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 61169-50:2015 Radio-frequency connectors - Sectional specification for RF coaxial connectors with inner diameter of outer conductors 4,11 mm with quick lock system. Characteristic impedance 50 Ohm (type QMA), 2015
- EN61169-50{2015}e.pdf [Go to Page]
- Foreword
- Endorsement notice
- Annex ZA (normative) Normative references to international publications with their corresponding European publications
- 30315315-VOR.pdf [Go to Page]
- English [Go to Page]
- CONTENTS
- FOREWORD
- INTRODUCTION
- 1 Scope
- 2 Normative references
- 3 Mating face and gauge information [Go to Page]
- 3.1 Dimensions – General connectors [Go to Page]
- 3.1.1 Connector with socket-centre contact
- 3.1.2 Connector with pin-centre contact
- 3.2 Gauges for general purpose connectors [Go to Page]
- 3.2.1 Gauge pins for socket-centre contact
- 3.2.2 Test procedure
- 4 Quality assessment procedures [Go to Page]
- 4.1 General
- 4.2 Ratings and characteristics (see Clause 5 of IEC 61169-1:2013)
- 4.3 Test schedule and inspection requirements [Go to Page]
- 4.3.1 Acceptance tests
- 4.4 Procedures for the quality conformance [Go to Page]
- 4.4.1 Quality conformance inspection
- 4.4.2 Qualification approval and its maintenance
- 5 Instructions for preparation of detail specifications [Go to Page]
- 5.1 General
- 5.2 Identification of the component
- 5.3 Performance
- 5.4 Marking, ordering information and related matters
- 5.5 Selection of tests, test conditions and severities
- 5.6 Blank detail specification pro-forma for type QMA connector
- 6 Marking [Go to Page]
- 6.1 Marking of component
- 6.2 Marking and contents of package
- Figures [Go to Page]
- Figure 1 – Connector with socket-centre contact (for dimensions, see Table 1)
- Figure 2 – Female centre contact (for dimensions, see Table 1)
- Figure 3 – Connector with pin-centre contact (for dimensions, see Table 2)
- Figure 4 – Details of pin-centre contact (for dimensions, see Table 2)
- Figure 5 – Gauge pin for socket-centre contact (for dimensions, see Table 3)
- Tables [Go to Page]
- Table 1 – Dimensions of connector with socket-centre contact
- Table 2 – Dimensions of connector with pin-centre contact
- Table 3 – Gauge dimensions for socket-centre contact
- Table 4 – Rating and characteristics
- Table 5 – Acceptance tests
- Table 6 – Periodic tests
- Français [Go to Page]
- SOMMAIRE
- AVANT-PROPOS
- INTRODUCTION
- 1 Domaine d’application
- 2 Références normatives
- 3 Informations relatives aux éléments d’accouplement et aux calibres [Go to Page]
- 3.1 Dimensions – Connecteurs généraux [Go to Page]
- 3.1.1 Connecteur avec contact central femelle
- 3.1.2 Connecteur avec contact central mâle
- 3.2 Calibres pour connecteurs à usage général [Go to Page]
- 3.2.1 Broches calibrées pour contact central femelle
- 3.2.2 Procédure d’essai
- 4 Procédures d’assurance de la qualité [Go to Page]
- 4.1 Généralités
- 4.2 Valeurs assignées et caractéristiques (voir l’Article 5 de l'IEC 61169-1:2013)
- 4.3 Programme d'essais et exigences de contrôle [Go to Page]
- 4.3.1 Essais d'acceptation
- 4.4 Procédures de conformité de la qualité [Go to Page]
- 4.4.1 Contrôle de conformité de la qualité
- 4.4.2 Homologation et maintenance
- 5 Instructions en vue de l'établissement des spécifications particulières [Go to Page]
- 5.1 Généralités
- 5.2 Identification du composant
- 5.3 Performance
- 5.4 Marquages, informations relatives aux commandes et sujets connexes
- 5.5 Choix des essais, conditions et sévérités des essais
- 5.6 Spécification particulière-cadre pro forma pour connecteur de type QMA
- 6 Marquage [Go to Page]
- 6.1 Marquage du composant
- 6.2 Marquage et contenu des emballages
- Figures [Go to Page]
- Figure 1 – Connecteur avec contact central femelle (pour les dimensions, voir le Tableau 1)
- Figure 2 – Contact central femelle (pour les dimensions, voir le Tableau 1)
- Figure 3 – Connecteur avec contact central mâle (pour les dimensions, voir le Tableau 2)
- Figure 4 – Détails du contact central mâle (pour les dimensions, voir le Tableau 2)
- Figure 5 – Broche calibrée pour contact central femelle (pour les dimensions, voir le Tableau 3)
- Tableaux [Go to Page]
- Tableau 1 – Dimensions du connecteur avec contact central femelle
- Tableau 2 – Dimensions du connecteur avec contact central mâle
- Tableau 3 – Dimensions du calibre pour contact central femelle
- Tableau 4 – Valeurs assignées et caractéristiques
- Tableau 5 – Essais d'acceptation
- Tableau 6 – Essais périodiques [Go to Page]