eLibrary >
BS EN ISO 6808:2014 Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids. Specification >
Expand All
TOC Search:
BS EN ISO 6808:2014 Plastics hoses and hose assemblies for suction and low-pressure discharge of petroleum liquids. Specification, 2014
- Contents Page
- Foreword
- Section sec_1
- Section sec_2
- Section sec_3
- Section sec_4
- Section sec_5
- Section sec_6
- Section sec_6.1
- Table tab_1
- Table tab_2
- Section sec_6.2
- Table tab_3
- Section sec_7
- Section sec_7.1
- Table tab_4
- Section sec_7.2
- Table tab_5
- Section sec_7.3
- Section sec_7.4
- Section sec_7.5
- Section sec_7.5.1
- Section sec_7.5.2
- Table tab_6
- Section sec_7.6
- Section sec_7.7
- Section sec_7.7.1
- Section sec_7.7.2
- Section sec_7.8
- Section sec_8
- Section sec_8.1
- Section sec_8.2
- Table tab_7
- Section sec_8.3
- Table tab_8
- Section sec_8.4
- Table tab_9
- Section sec_8.5
- Table tab_10
- Section sec_9
- Section sec_9.1
- Section sec_9.2
- Section sec_9.3
- Section sec_9.4
- Section sec_10
- Section sec_11
- Section sec_12
- Section sec_12.1
- Section sec_12.2
- Annex sec_A
- Table tab_A.1
- Annex sec_B
- Table tab_B.1
- Annex sec_C
- Annex sec_C.1
- Annex sec_C.2
- Annex sec_C.3
- Annex sec_C.4
- Annex sec_C.5
- Table tab_a
- Figure fig_C.1
- Annex sec_D
- Annex sec_D.1
- Annex sec_D.2
- Annex sec_D.3
- Reference ref_1
- Reference ref_2
- Annex D (normative) Coupling security test
- Bibliography
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Classification — Hose types
- 5 Construction and materials — Requirements
- 6 Dimensions and tolerances
- 6.1 Diameter
- 6.2 Length
- 7 Physical properties of finished hoses
- 7.1 Hydrostatic requirements at standard laboratory temperature
- 7.2 Hydrostatic requirements at 45 °C
- 7.3 Change in length (Type 2 only)
- 7.4 Suction resistance
- 7.5 Reinforcement fracture
- 7.6 Minimum bend test
- 7.7 Cold bend test
- 7.8 Electrical continuity
- 8 Physical properties of the flexible thermoplastics material
- 8.1 Loss in mass on heating
- 8.2 Tensile strength and elongation at break
- 8.3 Fuel resistance
- 8.4 Oil resistance
- 8.5 Resistance to accelerated ageing
- 9 Hose assemblies
- 9.1 Couplings and method of attachment
- 9.2 Test for security of coupling
- 9.3 Electrical bonding
- 9.4 Electrical wall resistance
- 10 Frequency of testing
- 11 Type tests
- 12 Marking
- 12.1 Hoses
- 12.2 Hose assemblies
- Annex A (normative) Test frequency
- Annex B (informative) Production tests
- Annex C (normative) Reinforcement fracture test
- Annex D (normative) Coupling security test
- Bibliography [Go to Page]