|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-C1941 2024ASTM C1941-24Active Standard: Standard Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers for JackingASTM C1941Scope 1.1 This specification covers the manufacturing requirements for precast reinforced concrete monolithic box sections that are intended to be installed using jacking techniques. The typical use of this type of product is for the construction of culverts and for the conveyance of storm water, industrial wastes and sewage. 1.2 The requirements of this specification are intended to supplement the existing manufacturing standards for precast reinforced concrete box sections and provide the additional manufacturing details required for box sections that will be installed using jacking techniques. The parent manufacturing standard for the precast reinforced concrete box sections is denoted as the “designated precast reinforced concrete box section manufacturing standard” throughout this document. The requirements included within shall supplement and supersede the designated precast reinforced concrete box section manufacturing standard when the box sections are to be used for jacking. Note 1: This specification is a manufacturing and purchase specification for precast reinforced concrete box sections installed using jacking techniques, to be utilized in conjunction with the designated precast reinforced concrete box section manufacturing standard. It is possible that such box sections will require a special design to withstand the anticipated longitudinal loading. Additional calculations and information beyond what are required for a non-jacked installed box section are required to establish maximum jacking forces. For calculating allowable jacking forces, ASCE 28 may be referenced. Note 2: This standard may be used to supplement existing standards for precast reinforced concrete box sections when the box sections will be installed using trenchless methods. Such “designated precast reinforced concrete box section manufacturing standards” include, but are not limited, to ASTM C1433, ASTM C1577, and AASHTO M259. 1.3 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords box section; culvert; jacking; joints; reinforced concrete; storm water; ICS Code ICS Number Code n/a DOI: 10.1520/C1941-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|