FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of ASTM-E1739 2015ASTM E1739-95-Reapproved2015Active Standard: Standard Guide for Risk-Based Corrective Action Applied at Petroleum Release SitesASTM E1739Scope 1.1 This is a guide to risk-based corrective action (RBCA), which is a consistent decision-making process for the assessment and response to a petroleum release, based on the protection of human health and the environment. Sites with petroleum release vary greatly in terms of complexity, physical and chemical characteristics, and in the risk that they may pose to human health and the environment. The RBCA process recognizes this diversity, and uses a tiered approach where corrective action activities are tailored to site-specific conditions and risks. While the RBCA process is not limited to a particular class of compounds, this guide emphasizes the application of RBCA to petroleum product releases through the use of the examples. Ecological risk assessment, as discussed in this guide, is a qualitative evaluation of the actual or potential impacts to environmental (nonhuman) receptors. There may be circumstances under which a more detailed ecological risk assessment is necessary (see Ref (1).2 1.2 The decision process described in this guide integrates risk and exposure assessment practices, as suggested by the United States Environmental Protection Agency (USEPA), with site assessment activities and remedial measure selection to ensure that the chosen action is protective of human health and the environment. The following general sequence of events is prescribed in RBCA, once the process is triggered by the suspicion or confirmation of petroleum release: 1.2.1 Performance of a site assessment; 1.2.2 Classification of the site by the urgency of initial response; 1.2.3 Implementation of an initial response action appropriate for the selected site classification; 1.2.4 Comparison of concentrations of chemical(s) of concern at the site with Tier 1 Risk Based Screening Levels (RBSLs) given in a look-up table; 1.2.5 Deciding whether further tier evaluation is warranted, if implementation of interim remedial action is warranted or if RBSLs may be applied as remediation target levels; 1.2.6 Collection of additional site-specific information as necessary, if further tier evaluation is warranted; 1.2.7 Development of site-specific target levels (SSTLs) and point(s) of compliance (Tier 2 evaluation); 1.2.8 Comparison of the concentrations of chemical(s) of concern at the site with the Tier 2 evaluation SSTL at the determined point(s) of compliance or source area(s); 1.2.9 Deciding whether further tier evaluation is warranted, if implementation of interim remedial action is warranted, or if Tier 2 SSTLs may be applied as remediation target levels; 1.2.10 Collection of additional site-specific information as necessary, if further tier evaluation is warranted; 1.2.11 Development of SSTL and point(s) of compliance (Tier 3 evaluation); 1.2.12 Comparison of the concentrations of chemical(s) of concern at the site at the determined point(s) of compliance or source area(s) with the Tier 3 evaluation SSTL; and 1.2.13 Development of a remedial action plan to achieve the SSTL, as applicable. 1.3 The guide is organized as follows: 1.3.1 Section 2 lists referenced documents, 1.3.2 Section 3 defines terminology used in this guide, 1.3.3 Section 4 describes the significance and use of this guide, 1.3.4 Section 5 is a summary of the tiered approach, 1.3.5 Section 6 presents the RBCA procedures in a step-by-step process, 1.3.6 Appendix X1 details physical/chemical and toxicological characteristics of petroleum products, 1.3.7 Appendix X2 discusses the derivation of a Tier 1 RBSL Look-Up Table and provides an example, 1.3.8 Appendix X3 describes the uses of predictive modeling relative to the RBCA process, 1.3.9 Appendix X4 discusses considerations for institutional controls, and 1.3.10 Appendix X5 provides examples of RBCA applications. 1.4 This guide describes an approach for RBCA. It is intended to compliment but not supersede federal, state, and local regulations. Federal, state, or local agency approval may be required to implement the processes outlined in this guide. 1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords ICS Code ICS Number Code 75.180.10 (Exploratory, drilling and extraction equipment) DOI: 10.1520/E1739-95R15 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|