|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Technical Bulletin
All
|
Description of BS EN ISO 5495:2005+A1:2016 2016This International Standard describes a procedure for determining whether there exists a perceptible sensory difference or a similarity between samples of two products concerning the intensity of a sensory attribute. This test is sometimes also referred to as a directional difference test or a 2-AFC test (Alternative Forced Choice). In fact, the paired comparison test is a forced choice test between two alternatives. NOTE The paired comparison test is the simplest existing classification test since it concerns only two samples. The method is applicable whether a difference exists in a single sensory attribute or in several, which means that it enables determination of whether there exists a perceptible difference concerning a given attribute, and the specification of the direction of difference, but it does not give any indication of the extent of that difference. The absence of difference for the attribute under study does not signify that there does not exist any difference between the two products. This method is only applicable if the products are relatively homogeneous. The method is effective
It is necessary to know, prior to carrying out the test, whether the test is a one-sided test (the test supervisor knows a priori the direction of the difference, and the alternative hypothesis corresponds to the existence of a difference in the expected direction) or a two-sided test (the test supervisor does not have any a priori knowledge concerning the direction of the difference, and the alternative hypothesis corresponds to the existence of a difference in one direction or the other). The paired test can also be used in order to compare two products in terms of preference. The different cases of use of the paired test are summarized in Figure 1. [Image removed.] EXAMPLE 1 (Case a) The production of a biscuit has been modified in order to render it more crisp. It is desired to check whether this increase is perceptible. Therefore it is necessary to try to highlight a difference to see whether the new product is perceived as being crispier than the usual product (control). EXAMPLE 2 (Case b) A manufacturer knows that the product may contain traces of an ingredient which imparts an off-flavour to the product. He therefore wishes to determine the maximum acceptable quantity so that the flavour difference with a reference product without this ingredient is barely perceptible and therefore without any regrettable consequences. EXAMPLE 3 (Case c) It is desired to produce a new soup and to compare two ingredients which will provide the salty flavour. For cost-intensive reasons, the ingredient which, at the same concentration, will provide the strongest salty flavour is sought. Therefore it is necessary to try to highlight a difference. It is not known a priori which ingredient will produce the strongest salty flavour. EXAMPLE 4 (Case d) A manufacturer of plastics used, in particular, by car manufacturers for dashboards is seeking, for economic reasons, to replace the usual lubricant by a new one, but does not wish that the new plastics formula be perceived as presenting less or more surface slip than the usual one. It is a question of determining whether, for a same concentration, the new lubricant provides the same “surface slip” level as the usual product. It is necessary to show that both lubricants are similar in terms of “surface slip”, but it is not known a priori which lubricant can produce the highest surface slip characteristics.
About BSIBSI Group, also known as the British Standards Institution is the national standards body of the United Kingdom. BSI produces technical standards on a wide range of products and services and also supplies certification and standards-related services to businesses. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|