Expand All
TOC Search:
BS EN 13480-3:2017+A4:2021 Metallic industrial piping - Design and calculation, 2021
- undefined
- 1 Modification to Clause 2, "Normative references"
- 2 Modification to 5.2.4, "Steel castings"
- 3 Modification to Annex A, "Dynamic effect"
- Annex A (informative)Dynamic effect [Go to Page]
- 4 Modification to Clause G.3, "Physical properties of steels"
- 5 Introduction of a new Clause G.4, "Material properties of carbon steel at elevated temperatures"
- 6 Introduction of a new Annex R, "Surveillance of components operating in the creep range"
- Annex R(informative)Surveillance of components operating in the creep range [Go to Page]
- 7 Modification to Bibliography
- 1 Modifications to European foreword
- 2 Modifications to Clause 2, Normative references
- 3 Modifications to 3.2, Symbols and units
- 4 Modifications to 4.2.3.4, Calculation pressure
- 5 Modifications to 4.3, Thickness
- 6 Modifications to 4.6, Dimensioning of piping components subject to pressure
- 7 Modifications to 5.2.1, Steels other than austenitic steels
- 8 Modifications to 5.2.4, Steels castings
- 9 Modifications to 5.2.5.1, General
- 10 Modifications to 5.3.2.1, Design conditions
- 11 Modifications to 6.2, Pipe bends and elbows
- 12 Modifications to 6.4.3, Specific symbols and abbreviations
- 13 Modifications to 6.4.10, Special forged reducers
- 14 Modifications to 6.5.2, Expansion joints
- 15 Modifications to 6.6, Bolted flange connections
- 16 Modifications to 6.6.4, Non-standard flange
- 17 Modifications to 7.1, Dished ends
- 18 Modifications to 7.1.3, Torispherical ends
- 19 Modifications to 7.2, Circular flat ends
- 20 Modifications to 7.2.3.3, Unflanged flat ends
- 21 Modifications to 7.2.4.1, General
- 22 Modifications to 7.2.5.2, Flat ends with openings
- 23 Modifications to 8.4.1, General
- 24 Modifications to 8.4.4, Reinforced single openings with 0,8 < d/D ≤ 1,0
- 25 Modifications to 8.5.2, Reinforced openings with d/D ≤ 0,8
- 26 Modifications to 8.6.1, Cylindrical Y-pieces
- 27 Modifications to 10.3.2, Simplified fatigue analysis
- 28 Modifications to 10.3.2.3, Determination of allowable number of load cycles
- 29 Modifications to 10.4.2, Design guidance
- 30 Modifications to 11.3, Symbols
- 31 Modifications to 12.2.3, Displacement strains
- 32 Modifications to 12.2.5, Stress range
- 33 Modifications to 12.2.7.1, Thermal expansion data
- 34 Modifications to 12.2.10.2, Formal analysis required
- 35 Modifications to C.1.3, Design of expansion joints
- 36 Modifications to D.4.1, Introduction
- 37 Modifications to D.4.4, Flange construction
- 38 Modifications to D.4.6, Gaskets
- 39 Modifications to D.5.2, Bolt loads and areas
- 40 Modifications to D.5.4.2, Stress limits
- 41 Modifications to E.2.1, Angles and areas
- 42 Modifications to F.2, Measures to be taken when the calculated fatigue life has been reached
- 43 Modifications to L.2, Symbols
- 44 Modifications to L.4, Allowable compressive stress
- 45 Modifications to Annex P, Recommended gaskets for industrial piping
- 46 Modifications to Q.3, Explanatory notes for Table Q.1
- 47 Modifications to Bibliography
- 1 Modifications to Clause 2, Normative references
- 2 Modifications to 13.11, Manufacturing of pipe supports
- 3 Modifications to Annex N, Documentation of supports [Go to Page]