Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 17344:2020 Agricultural machinery. Self-propelled agricultural and forestry vehicles. Requirements for braking, 2020
- undefined
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Construction requirements [Go to Page]
- 4.1 Braking components and braking surfaces
- 4.2 Functions of the braking system and the basic requirements
- 4.3 Axles subject to braking
- 4.4 Brake assisted steering function
- 4.5 Requirements for controls
- 4.6 Requirements for energy sources and energy reserves
- 4.7 Distribution of braking forces
- 4.8 Specific requirements for hydraulic braking systems using brake fluid
- 4.9 Specific requirements for the electric transmission of the parking brake system
- 4.10 Warning signals for brake failure
- 4.11 Vehicles fitted with spring brakes [Go to Page]
- 4.11.1 Use of a spring brake as service brake
- 4.11.2 Use of a spring brake as secondary brake
- 4.11.3 Pressure requirements
- 4.11.4 Auxiliary release system
- 5 Requirements regarding brake testing and performance [Go to Page]
- 5.1 Braking performance parameters
- 5.2 Conditions for measuring braking performance during road tests
- 5.3 Performance testing on vehicles with a stepless drive
- 5.4 Type-0 braking test (ordinary performance test with brakes cold)
- 5.5 Secondary braking performance
- 5.6 Parking braking performance
- 5.7 Type – I braking test (fade test)
- 5.8 Hot performance
- 5.9 Requirements applying to the response time for the service braking system
- 5.10 Maximum unbraked towable mass
- Annex A (normative)Category of energy sources [Go to Page]
- A.1 Pneumatic braking system [Go to Page]
- A.1.1 Symbols specific to this section
- A.1.2 Conditions of measurement
- A.1.3 Capacity of compressors on vehicles [Go to Page]
- A.1.3.1 The time t1 recorded for the least favoured energy storage device shall not exceed:
- A.1.3.2 The time t2 recorded for the least favoured energy storage device shall not exceed:
- A.1.4 Additional test [Go to Page]
- A.1.4.1 When the vehicle is equipped with an auxiliary equipment reservoir or reservoirs with a total capacity exceeding 20 % of the total capacity of the energy storage devices for braking, an additional test shall be carried out during the course of which there shall be no interference with the functioning of the valves controlling the filling of the auxiliary equipment reservoir(s). A check shall be made during the course of this test that the period t3 required to bring about a rise in the pressure in the brake reservoirs from 0 to p2 is less than:
- A.1.4.2 The pressure test connections shall comply with Clause 4 of ISO 3583:1984.
- A.2 Hydraulic braking system [Go to Page]
- A.2.2 Conditions of measurement are
- A.2.3 The time t required for the pressure to rise from p2 to p1 in the energy storage devices shall not exceed 30 s.
- Annex B (normative)Capacity of energy storage devices [Go to Page]
- B.1 Pneumatic energy storage devices [Go to Page]
- B.1.1 Vehicles on which the operation of the braking system depends on the use of compressed air shall be fitted with reservoirs of a capacity meeting the following requirements of this section.
- B.1.2 However, the reservoirs shall not be required to be of a prescribed capacity if the braking system is such that in the absence of any energy reserve it is possible with the service braking system control device to achieve a braking performance at least equal to that prescribed for the secondary braking system.
- B.1.3 When verifying compliance with the following requirements the brakes shall be adjusted as closely as possible.
- B.1.4 The air brake reservoirs of vehicles shall be so designed that after eight full-stroke actuations of the service braking system control device, the pressure remaining in the air brake reservoir shall be not less than the pressure required to obtain the specified secondary braking performance. [Go to Page]
- B.1.4.1 The initial pressure in the reservoirs shall be that indicated by the manufacturer. This pressure shall be such as to enable the prescribed performance for the service braking system to be achieved. The initial pressure shall be stated in the test report.
- B.1.4.2 The reservoir or reservoirs shall not be replenished during the capacity test; in addition, the reservoir or reservoirs of auxiliary equipment, if any shall be isolated.
- B.2 Capacity of hydraulic storage devices [Go to Page]
- B.2.1 Vehicles on which the operation of the braking system requires the use of stored energy provided by hydraulic fluid under pressure shall be equipped with energy storage devices of a capacity meeting the following requirements.
- B.2.2 Energy storage devices used as pulsation dampers in hydraulic braking systems are not to be considered as energy storage devices.
- B.2.3 However, the energy storage devices shall not be required to be of a prescribed capacity if the braking system is such that in the absence of any energy reserve it is possible with the service braking system control device to achieve a braking performance at least equal to that prescribed for the secondary braking system.
- B.2.4 In verifying compliance with the following requirements, the brakes shall be adjusted as closely as possible.
- B.2.5 After eight full-stroke actuations of the service braking system control device, it shall still be possible to achieve, on the ninth application, the performance prescribed for the secondary braking system. [Go to Page]
- B.2.5.1 Testing shall commence at a pressure that may be specified by the manufacturer but is not higher than the cut-in pressure.
- B.2.5.2 The energy storage devices shall not be fed during the capacity test; in addition, any energy storage devices for auxiliary equipment shall be isolated.
- B.2.6 Vehicles equipped with a hydraulic service braking system with stored energy and not consisting of two independent circuits shall be deemed to satisfy that point if the following requirements are met: [Go to Page]
- B.2.6.1 After any single transmission failure it shall still be possible after eight full-stroke actuations of the service braking system control device, to achieve, at the ninth application, at least the performance prescribed for the secondary braking system.
- B.2.6.2 With the energy source stationary or operating at a speed corresponding to the engine idling speed, any transmission failure may be induced. Before inducing such a failure the energy storage device(s) shall be at a pressure that may be specified by the manufacturer but not exceeding the cut-in pressure.
- Annex C (normative)Test report [Go to Page]