Already a subscriber? 
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN 754-1:2016 - TC Tracked Changes. Aluminium and aluminium alloys. Cold drawn rod/bar and tube - Technical conditions for inspection and delivery, 2020
- 30324461_new.pdf [Go to Page]
- Contents Page
- European foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Ordering information
- 5 Requirements [Go to Page]
- 5.1 Production and manufacturing processes
- 5.2 Quality control
- 5.3 Chemical composition limits
- 5.4 Mechanical properties
- 5.5 Freedom from surface defects
- 5.6 Tolerances on dimensions and form
- 5.7 Stress corrosion cracking resistance
- 5.8 Additional requirements
- 6 Test procedures [Go to Page]
- 6.1 Sampling [Go to Page]
- 6.1.1 Samples for chemical analysis
- 6.1.2 Specimens for mechanical testing [Go to Page]
- 6.1.2.1 Location and size
- 6.1.2.2 Orientation
- 6.1.2.3 Identification
- 6.1.2.4 Preparation
- 6.1.2.5 Number
- 6.1.3 Test pieces for tensile test [Go to Page]
- 6.1.3.1 Identification
- 6.1.3.2 Machining
- 6.1.3.3 Number, type and location of test pieces
- 6.2 Test methods [Go to Page]
- 6.2.1 Chemical composition limits
- 6.2.2 Tensile testing
- 6.2.3 Brinell hardness testing
- 6.2.4 Measurement of dimensions
- 6.2.5 Surface finish
- 6.2.6 Resistance to stress corrosion cracking
- 6.2.7 Additional tests
- 6.3 Re-tests [Go to Page]
- 6.3.1 Chemical composition limits
- 6.3.2 Mechanical properties
- 6.3.3 Other properties
- 7 Inspection documents
- 8 Marking of products
- 9 Packaging
- 10 Arbitration
- Annex A (normative) Location of test pieces
- A.1 Round, square and hexagonal bar
- A.1.1 For diameter (D) or width across flats (S) up to and including 40 mm:
- Figure A.1 — Round, square and hexagonal bar
- A.1.2 For diameter (D) or width across flats (S) over 40 mm:
- Figure A.2 — Round, square and hexagonal bar
- A.2 Rectangular bar
- A.2.1 For thickness up to and including 12,5 mm:
- A.2.2 For thickness (T) over 12,5 mm and up to and including 40 mm:
- Figure A.3 — Rectangular bar
- A.2.3 For thickness (T) exceeding 40 mm:
- Figure A.4 — Rectangular bar
- A.3 Tube
- Table A.1 — Test piece requirements for tubes
- Annex B (normative) Resistance to stress-corrosion cracking for alloy EN AW-7075 in tempers T73, T7351, T73510 and T73511 – Electrical conductivity
- Table B.1 — Lot acceptance criteria on tempers T73, T7351, T73510 and T73511 for alloy EN AW-7075
- Bibliography [Go to Page]
