Already a subscriber?
MADCAD.com Free Trial
Sign up for a 3 day free trial to explore the MADCAD.com interface, PLUS access the
2009 International Building Code to see how it all works.
If you like to setup a quick demo, let us know at support@madcad.com
or +1 800.798.9296 and we will be happy to schedule a webinar for you.
Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN IEC 60938-1:2021 Fixed inductors for electromagnetic interference suppression - Generic specification, 2021
- undefined
- Annex ZA (normative)Normative references to international publicationswith their corresponding European publications
- English [Go to Page]
- CONTENTS
- FOREWORD
- INTRODUCTION [Go to Page]
- Figure 1 – Relevant specification
- 1 Scope
- 2 Normative references
- Figures
- 3 Terms, definitions and conventions [Go to Page]
- 3.1 Terms and definitions
- 3.2 Conventions
- 4 General requirements [Go to Page]
- 4.1 General
- 4.2 Preferred values [Go to Page]
- 4.2.1 General
- 4.2.2 Rated current
- 4.2.3 Temperature de-rated current
- 4.3 Information to be given in a detail specification [Go to Page]
- 4.3.1 General
- 4.3.2 Outline drawing and dimensions
- Figure 2 – Relation between ambient temperature and applied current [Go to Page]
- 4.3.3 Mounting
- 4.3.4 Ratings and characteristics
- 4.4 Insulated inductors
- 4.5 Marking
- 5 Tests and measurement procedures [Go to Page]
- 5.1 General
- 5.2 Standard atmospheric conditions
- 5.3 Visual examination
- 5.4 Insulation resistance
- Tables [Go to Page]
- Table 1 – Standard atmospheric conditions
- 5.5 Voltage test
- Table 2 – Measuring voltage for insulation resistance testing
- 5.6 Inductance
- 5.7 Resistance
- 5.8 Insertion loss
- 5.9 Temperature rise
- 5.10 Impulse voltage
- 5.11 Endurance
- 5.12 Robustness of terminations
- 5.13 Vibration
- 5.14 Shock
- 5.15 Resistance to soldering heat
- Figure 3 – Temperature profile for reflow simulation
- 5.16 Solderability [Go to Page]
- 5.16.1 General
- 5.16.2 Preconditioning
- Table 3 – Temperatures for reflow simulation with different solder paste alloy types [Go to Page]
- 5.16.3 Test procedure
- 5.16.4 Final inspection, measurements, and requirements
- 5.17 Rapid change of temperature
- 5.18 Container sealing
- 5.19 Climatic sequence [Go to Page]
- 5.19.1 General
- 5.19.2 Dry heat
- 5.19.3 Damp heat, cyclic, test Db, first cycle
- 5.19.4 Cold
- 5.19.5 Low air pressure
- 5.19.6 Damp heat, cyclic, test Db, remaining cycles
- Table 4 – Number of remaining cycles for damp heat
- 5.20 Damp heat, steady state
- 5.21 Passive flammability
- 5.22 Glow wire
- 5.23 Ball pressure
- 5.24 Component solvent resistance
- 5.25 Solvent resistance of marking
- Annex A (normative) Measuring points for electrical tests and measurements [Go to Page]
- A.1 General
- A.2 Foil method
- A.3 Method for inductors with mounting devices
- Table A.1 – Measuring points for electrical tests
- A.4 Vblock method
- Figure A.1 – Examples how to connect electrical tests
- Annex B (normative) Requirements for earth inductors [Go to Page]
- Table B.1 – Minimum copper cross-sectional area of earth inductor’s winding
- Annex C (normative) Example of a suitable circuit for the voltage endurance test [Go to Page]
- Figure C.1 – Test circuit for endurance voltage
- Annex X (informative) Cross-references to the previous edition of this document
- Bibliography [Go to Page]