Security check
Please login to your personal account to use this feature.
Please login to your authorized staff account to use this feature.
Are you sure you want to empty the cart?
BS EN IEC 61010-2-032:2021+A11:2021 Safety requirements for electrical equipment for measurement, control and laboratory use - Particular requirements for hand-held and hand-manipulated current sensors for electrical test and measurement, 2022
- undefined
- European foreword
- Endorsement notice [Go to Page]
- 1 General
- 2 Modification to 3.2, “Parts and accessories”
- 3 Modification to 6.8.3.2, “The d.c. voltage test”
- 4 Modifications to 8.101, “Jaw ends abrasion test”
- 5 Modifications to K.101.4.1, “General”
- 6 Addition of Annex ZA, “Normative references to international publicationswith their corresponding European publications”
- Annex ZA(normative)Normative references to international publicationswith their corresponding European publications
- 7 Addition of Annex ZZ, “Relationship between this European standard and the safety objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be covered”
- Annex ZZ (informative)Relationship between this European standard and the safety objectives of Directive 2014/35/EU [2014 OJ L96] aimed to be covered
- English [Go to Page]
- CONTENTS
- FOREWORD
- INTRODUCTION
- 1 Scope and object [Go to Page]
- Figure 101 – Examples of current sensors and their parts
- 2 Normative references
- 3 Terms and definitions
- Figures
- 4 Tests
- 5 Marking and documentation
- Tables [Go to Page]
- Table 1 – Symbols
- 6 Protection against electric shock [Go to Page]
- Table 101 – Clearances and creepage distances for measuring circuit terminals with hazardous live conductive parts up to 1 000 V a.c. or 1 500 V d.c.
- Figure 102 – Clearance between the protective barrier to the jaws and to the hazardous live conductor
- 7 Protection against mechanical hazards
- 8 Resistance to mechanical stresses [Go to Page]
- Figure 103 – Abrasion test of the jaw ends
- Table 102 – Energy level for jaw impact test
- Figure 104 – Impact points for jaw impact test
- Figure 105 – Indentation device
- 9 Protection against the spread of fire
- 10 Equipment temperature limits and resistance to heat [Go to Page]
- Table 103 – Pull forces for endcaps of flexible current sensors
- 11 Protection against hazards from fluids and solid foreign objects
- 12 Protection against radiation, including laser sources, and against sonic and ultrasonic pressure
- 13 Protection against liberated gases and substances, explosion and implosion
- 14 Components and subassemblies
- 15 Protection by interlocks
- 16 Hazards resulting from application
- 17 Risk assessment [Go to Page]
- Table 104 – Impulse voltages
- Figure 106 – Test probe to check protection against short-circuits
- Figure 107 – Use of the test probe of Figure 106
- Table 105 – Thickness of the test probe of Figure 106 and test voltages
- Annexes [Go to Page]
- Annex D (normative) Parts between which insulation requirements are specified (see 6.4, 6.5.3, 6.9.101 and 6.101)
- Figure D.101 – Parts of current sensors (see also Table D.101)
- Table D.101 – Insulation requirements for current sensors
- Annex F (normative) Routine tests
- Annex K (normative) Insulation requirements not covered by 6.7
- Table K.101 – Clearances of measuring circuitsrated for measurement categories
- Table K.102 – a.c. test voltages for testing electric strength of solid insulation in measuring circuits rated for measurement categories
- Table K.103 – Impulse test voltages for testing electric strength of solid insulation in measuring circuits rated for measurement categories
- Table K.104 –Test voltages for testing long-term stressof solid insulation in measuring circuits rated for measurement categories
- Table K.105 – Minimum values for distance or thickness of solid insulation in measuring circuits rated for measurement categories III and IV
- Annex L (informative) Index of defined terms
- Annex AA (normative) Measurement categories
- Figure AA.1 – Example to identify the locations of measuring circuits
- Table AA.1 – Characteristics of measurement categories
- Annex BB (informative) Hazards pertaining to measurements performed in certain environments
- Annex CC (informative) 4-mm "banana" terminals
- Figure CC.1 – Recommended dimensions of 4-mm terminals
- Annex DD (informative) Flowchart for insulation according to the type of circuit
- Figure DD.1 – Requirements for clearance, creepage distance and solid insulation
- Annex EE (normative) Clamp multimeter
- Figure EE.1 – Examples of clamp multimeters
- Bibliography [Go to Page]
