|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-A1072/A1072M 2020ASTM A1072/A1072M-11-Reapproved2020Active Standard: Standard Specification for Zinc-5 % Aluminum (Hot-Dip) Coatings on Iron and Steel ProductsASTM A1072/A1072MScope 1.1 This specification covers the requirements for zinc-5 % aluminum coated, by the hot-dip process on iron and steel products. The coating may also contain small amounts of elements other than zinc and aluminum that are intended to improve processing and the characteristics of the coated product. These metallic coatings include zinc- 5 %-aluminum (Zn-5Al), zinc-5 %-aluminum-mischmetal (Zn-5Al-MM) and zinc-5 %-aluminum-magnesium (Zn- %Al-Mg). 1.2 This specification covers both un-fabricated products and fabricated products, for example, assembled steel products, structural steel fabrications, large tubes already bent or welded before hot-dip coating, and wire work fabricated from uncoated steel wire. This specification, also, covers steel forgings and iron castings incorporated into pieces fabricated, before hot-dip coating or which are too large to be centrifuged (or otherwise handled to remove excess molten bath metal). 1.3 Fabricated reinforcing steel bar assemblies are covered by the present specification. 1.4 This specification is applicable to orders in either inch-pound units (as A1072) or SI units (as A1072M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in parentheses. Each system shall be used independently of the other without combining values in any way. In the case of orders in SI units, all testing and inspection shall be done using the metric equivalent of the test or inspection method as appropriate. In the case of orders in SI units, such shall be stated to the hot-dip coater when the order is placed. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords coatings—zinc 5 % aluminum; galvanized coatings; steel products—metallic coated; zinc 5 % aluminum coatings—steel products; ICS Code ICS Number Code 25.220.40 (Metallic coatings) DOI: 10.1520/A1072_A1072M-11R20 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|