|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-A1126 2023ASTM A1126-23Active Standard: Standard Specification for Magnetic Pure IronASTM A1126Scope 1.1 This specification covers the requirements for mill-cast and wrought magnetic pure iron containing no more than 0.0060 % carbon and a typical total iron content of 99.9 %. The magnetic characteristics exhibited by magnetic pure iron are made possible by the absence of alloying elements during production. 1.2 This specification also covers magnetic pure iron supplied in a form and condition which allows for subsequent heat treatment to achieve desired magnetic characteristics. 1.3 Magnetic pure iron may be supplied in forms including hot-rolled strip, sheet, plate, bar, billet, and slab; cold-rolled strip and sheet; mill-cast slab and bloom; forgings; and drawn wire and rod. 1.4 This specification does not cover cast parts or iron powders capable of being processed into magnetic components. Please refer to the following ASTM standards for information regarding powdered metal materials and magnetic components: Specifications A811, A839, and A904. 1.5 This specification does not cover material that contains constituent elements sufficient to increase the carbon content above 0.0060 % or to decrease the iron content below 99.9 %. Refer to Specification A848 for properties of low carbon magnetic iron. 1.6 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to customary (cgs-emu and inch-pound) units which are provided for information only and are not considered standard. 1.6.1 There are selected values presented in two units, both of which are acceptable SI units. These are differentiated by the word “or,” as in “g/cm3, or, (kg/m3).” 1.7 Acceptance values may be generated by an independent party. This specification accepts reports from producers or intermediate suppliers. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords coercive field strength; magnetic field strength; magnetic flux density; magnetic polarization; magnetic pure iron; relative maximum permeability; 99.9 % iron; ICS Code ICS Number Code 77.140.40 (Steels with special magnetic properties) DOI: 10.1520/A1126-23 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|