Search book title
Filters:
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(338)
ACI
(617)
AECDAILY
(599)
AISC
(55)
ASA
(234)
ASCE
(1006)
ASHRAE
(696)
ASME
(2183)
ASSE
(117)
ASTM
(95207)
AWC
(63)
AWWA
(575)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(95735)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(324)
IEEE
(7050)
IES
(241)
ISEA
(21)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1667)
TCNA
(18)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(25)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    A414/A414M-24 Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels (Redline)
    Edition: 2024
    $91.10
    Unlimited Users per year

Description of ASTM-A414/A414M 2024

ASTM A414/A414M-24

Redline Standard: Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy for Pressure Vessels




ASTM A414/A414M

Scope

1.1 This specification2 covers hot-rolled carbon steel sheet for pressure vessels involving fusion welding or brazing. Welding and brazing technique is of fundamental importance and shall be in accordance with commercial practices.

1.2 The following grades are included in this specification:

 

Mechanical Requirements

 

Yield Strength, min

Tensile Strength, min

Grade

ksi

MPa

ksi

MPa

A

25

170

45

310

B

30

205

50

345

C

33

230

55

380

D

35

240

60

415

E

38

260

65

450

F

42

290

70

485

G

45

310

75

515

H

45

310

75

515

1.3 Hot-rolled carbon steel sheet is generally furnished in cut lengths and to decimal thickness only. Coils may be furnished, provided tension test specimens are taken to represent the front end, middle, and back end of the slab as required by the mechanical property requirements in section 6.1, for Tensile Strength. The purchaser should recognize this may require cutting the coils to obtain test samples and results in half-size coils. The sheet shall be furnished to the following size limits:

 

Width, in. [mm]

 

 

Thickness, in. [mm]

Over 12 [Over 300]

 

 

0.270 to 0.230 [7.0 to 6.0]

 sheet (coils only)

Under 0.230 to 0.057 [6.0 to 1.5]

 sheet

1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.5 Tolerances are found in General Requirements Specifications A568/A568M and A635/A635M. The appropriate General Requirements specification is applied based on the thickness and width of the product ordered.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Keywords

carbon steel sheet; pressure vessel steels; steel sheet ;


ICS Code

ICS Number Code 77.140.30 (Steels for pressure purposes)


DOI: 10.1520/A0414_A0414M-24

GROUPS
US LOCAL CODES
US Territory Code Adoptions / Amendments
District of Columbia
Guam
Northern Marianas Islands
Puerto Rico
US Virgin Islands
US State Code Adoptions / Amendments
AL AK AZ AR CA CO CT DE
FL GA HI ID IL IN IA KS
KY LA ME MD MA MI MN MS
MO MT NE NV NH NJ NM NY
NC ND OH OK OR PA RI SC
SD TN TX UT VT VA WA WV
WI WY       
X
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69 70
71 72 73 74 75 76 77 78 79 80
81 82 83 84 85 86 87 88 89 90
91 92 93 94 95 96 97 98 99 100