Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
Tour
eLibrary
Store
Search book title
Filters:
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(338)
ACI
(621)
AECDAILY
(599)
AISC
(55)
ASA
(234)
ASCE
(1006)
ASHRAE
(696)
ASME
(2183)
ASSE
(117)
ASTM
(95207)
AWC
(63)
AWWA
(584)
BHMA
(124)
BICSI
(33)
BIFMA
(21)
BOMA
(20)
BSI
(96195)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(324)
IEEE
(7050)
IES
(241)
ISEA
(21)
Joint Commission
(184)
Joint Commission Int.
(1)
NETA
(6)
NFPA
(1667)
TCNA
(18)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(28)
MN
(27)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    A531/A531M-24 Standard Practice for Ultrasonic Examination of Turbine-Generator Steel Retaining Rings (Redline)
    Edition: 2024
    $103.58
    Unlimited Users per year

Description of ASTM-A531/A531M 2024

ASTM A531/A531M-24

Redline Standard: Standard Practice for Ultrasonic Examination of Turbine-Generator Steel Retaining Rings




ASTM A531/A531M

Scope

1.1 This practice covers ultrasonic examination of turbine-generator retaining rings produced in accordance with Specifications A288 and A289/A289M with an inside diameter to wall thickness ratio equal to or greater than 5:1 and with wall thicknesses from 1 in. to 4 in. [25 mm to 102 mm].

1.2 Forgings may be inspected by either the contact or the immersion methods, or combinations thereof, as agreed upon between the manufacturer and the purchaser.

1.3 Supplementary requirements of an optional nature are provided for use at the option of the purchaser. The supplementary requirements shall apply only when specified individually by the purchaser in the purchase order or contract.

1.4 This practice is expressed in inch-pound and SI units; however, unless the purchase order or contract specifies the applicable “M” specification designation (SI units), the inch-pound units shall apply. The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the practice, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Keywords

angle beam examination; back-reflection; contact method; generator; immersion method; longitudinal wave testing; nondestructive testing; reference-block; reference-notch; retaining rings; shear wave testing; steel forgings-alloy; turbine; ultrasonic apparatus; ultrasonic couplants; ultrasonic examination;


ICS Code

ICS Number Code 21.060.60 (Rings, bushes, sleeves, collars)


DOI: 10.1520/A0531_A0531M-24

GROUPS
US LOCAL CODES
US Territory Code Adoptions / Amendments
District of Columbia
Guam
Northern Marianas Islands
Puerto Rico
US Virgin Islands
US State Code Adoptions / Amendments
AL AK AZ AR CA CO CT DE
FL GA HI ID IL IN IA KS
KY LA ME MD MA MI MN MS
MO MT NE NV NH NJ NM NY
NC ND OH OK OR PA RI SC
SD TN TX UT VT VA WA WV
WI WY       
X
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69 70
71 72 73 74 75 76 77 78 79 80
81 82 83 84 85 86 87 88 89 90
91 92 93 94 95 96 97 98 99 100