1. Scope

1.1 This specification covers polymer precoated corrugated steel pipe intended for use for storm water drainage, underdrains, the construction of culverts, and similar uses. Pipe covered by this specification is not normally used for the conveyance of sanitary or industrial wastes. The steel sheet used in fabrication of the pipe has a polymer protective coating over a metallic coating of zinc, 55% aluminum-zinc alloy, or zinc-5% aluminum-mischmetal alloy.

1.2 The polymer precoating provides extra protection of the base metal against corrosion or abrasion, or both, in addition to that provided by the metallic coating. Some severe environments may cause corrosion problems to accessory items such as rivets or coupling band hardware that does not have a polymer coating. Additional protection for polymer precoated corrugated steel pipe can be provided by use of coatings applied after fabrication of the pipe as described in Specification A849.

1.3 This specification does not include requirements for bedding, backfill, or the relationship between earth cover load and sheet thickness of the pipe. Experience has shown that the successful performance of this product depends upon the proper selection of sheet thickness, type of bedding and backfill, controlled manufacture in the plant, and care in the installation. The installation procedure is described in Practice A798.

1.4 This specification is applicable to orders in either inch-pound units as A762, or in SI units as A762M. Inch-pound units and SI units are not necessarily equivalent. SI units are shown in brackets in the text for clarity, but they are the applicable values when the material is ordered to A762M.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A90/A90M Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware

A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

A493 Specification for Stainless Steel Wire and Wire Rods for Cold Heading and Cold Forging

A563 Specification for Carbon and Alloy Steel Nuts

A563M Specification for Carbon and Alloy Steel Nuts (Metric)

A742/A742M Specification for Steel Sheet, Metallic Coated and Polymer Precoated for Corrugated Steel Pipe

A760/A760M Specification for Corrugated Steel Pipe, Metallic-Coated for Sewers and Drains

A780 Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings

A796/A796M Practice for Structural Design of Corrugated Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary Sewers and Other Buried Applications

A798/A798M Practice for Installing Factory-Made Corrugated Steel Pipe for Sewers and Other Applications

A849 Specification for Post-Applied Coatings, Pavings, and Linings for Corrugated Steel Sewer and Drainage Pipe

A929/A929M Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process for Corrugated Steel Pipe

B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel

B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

C443 Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets

D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers

D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber

F568M Specification for Carbon and Alloy Steel Externally Threaded Metric Fasteners (Metric)

Keywords

corrugated steel pipe; drainage pipe; metallic coated steel pipe; polymer precoated; sewer pipe; Corrugated steel sewer/drain pipe--specifications; Metallic-coated steel pipe--specifications; Polymer coatings--steel; Sewer pipe (steel)--specifications; Steel pipe--specifications;

ICS Code

ICS Number Code 23.040.10 (Iron and steel pipes)

DOI: 10.1520/A0762_A0762M-00

ASTM International is a member of CrossRef.