Abstract

This specification covers UNS R60001, R60802, R60804, and R60901 wrought zirconium and zirconium alloy bars, rods, and wires. All material grades covered should conform to the required chemical composition requirements. Elements that are intentionally added to the melt should be identified, analyzed and reported in the chemical analysis. The zirconium and zirconium alloys should be made from ingots produced by vacuum or plasma arc melting, vacuum electron-beam melting, a combination of the three methods, or other melting processes conventionally used for reactive metals. All processes should be performed in furnaces specifically for reactive metals. Mill products included in this specification should be formed with conventional extrusion, forging, or rolling equipment that is used in primary ferrous and nonferrous plants. The cold worked and annealed materials should be in fully annealed condition unless otherwise specified. Hot worked shapes should be furnished in not descaled, mechanically descaled, or mechanically descaled and pickled finish, while cold-worked shapes should be furnished in cold-worked, ground, or pickled finish.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers four grades of wrought zirconium and zirconium alloy bars, rod, and wire as follows:

1.1.1 R60001 Unalloyed grade,

1.1.2 R60802 Zirconium-Tin alloy (Zircaloy 2),

1.1.3 R60804 Zirconium-Tin alloy (Zircaloy 4), and

1.1.4 R60901 Zirconium-Niobium alloy.

1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm ² , the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.

1.3 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

B350/B350M Specification for Zirconium and Zirconium Alloy Ingots for Nuclear Application

E8/E8M Test Methods for Tension Testing of Metallic Materials

E21 Test Methods for Elevated Temperature Tension Tests of Metallic Materials

E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

E114 Practice for Ultrasonic Pulse-Echo Straight-Beam Contact Testing

E214 Practice for Immersed Ultrasonic Testing by the Reflection Method Using Pulsed Longitudinal Waves

G2/G2M Test Method for Corrosion Testing of Products of Zirconium, Hafnium, and Their Alloys in Water at 680F [360C] or in Steam at 750F [400C]

Keywords

(metal); (metal) alloy; (metal) bar; (metal) rod; (metal) wire; (metal) (nuclear applications); Nuclear applications/materials--zirconium/zirconium alloys; Zirconium metals--specifications; Zirconium alloys (for nuclear applications)--specifications; UNS R60001 (Zr/Zr alloy for nuclear applications); UNS R60802 (Zr/Zr alloy for nuclear applications); UNS R60804 (Zr/Zr alloy for nuclear applications); UNS R60901 (Zr/Zr alloy for nuclear applications);

ICS Code

ICS Number Code 77.140.60 (Steel bars and rods); 77.140.65 (Steel wire, wir ropes and link chains)

DOI: 10.1520/B0351_B0351M-08E01

ASTM International is a member of CrossRef.

ASTM B351 / B351M