1. Scope

1.1 This specification covers all forms of fiber-reinforced concrete that are delivered to a purchaser with the ingredients uniformly mixed, and that can be sampled and tested at the point of delivery. It does not cover the placement, consolidation, curing, or protection of the fiber-reinforced concrete after delivery to the purchaser.

1.2 Certain sections of this specification are also applicable to fiber-reinforced concrete intended for shotcreting by the dry-mix process when sampling and testing of concrete is possible only at the point of placement. In this case, the sections dealing with batching plant, mixing equipment, mixing and delivery, and measurement of workability and air content, are not applicable.

1.3 This specification does not cover thin-section glass fiber-reinforced concrete manufactured by the spray-up process that is under the jurisdiction of ASTM Subcommittee C27.40.

1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.5 The following precautionary statement pertains only to the test method portion, Sections 15 and 18, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A820/A820M Specification for Steel Fibers for Fiber-Reinforced Concrete

C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field

C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens

C42/C42M Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete

C94/C94M Specification for Ready-Mixed Concrete

C125 Terminology Relating to Concrete and Concrete Aggregates

C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

C143/C143M Test Method for Slump of Hydraulic-Cement Concrete

C150 Specification for Portland Cement

C172 Practice for Sampling Freshly Mixed Concrete

C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method

C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory

C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

C387 Specification for Packaged, Dry, Combined Materials for Mortar and Concrete

C567 Test Method for Determining Density of Structural Lightweight Concrete

C666/C666M Test Method for Resistance of Concrete to Rapid Freezing and Thawing

C684 Test Method for Making, Accelerated Curing, and Testing Concrete Compression Test Specimens

C685/C685M Specification for Concrete Made by Volumetric Batching and Continuous Mixing

C1077 Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation

C1140 Practice for Preparing and Testing Specimens from Shotcrete Test Panels

C1385/C1385M Practice for Sampling Materials for Shotcrete

C1399 Test Method for Obtaining Average Residual-Strength of Fiber-Reinforced Concrete

C1436 Specification for Materials for Shotcrete

C1480 Specification for Packaged, Pre-Blended, Dry, Combined Materials for Use in Wet or Dry Shotcrete Application

C1550 Test Method for Flexural Toughness of Fiber Reinforced Concrete (Using Centrally Loaded Round Panel)

C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete

C1604/C1604M Test Method for Obtaining and Testing Drilled Cores of Shotcrete

C1609/C1609M Test Method for Flexural Performance of Fiber-Reinforced Concrete (Using Beam With Third-Point Loading)

C1666/C1666M Specification for Alkali Resistant (AR) Glass Fiber for GFRC and Fiber-Reinforced Concrete and Cement

D6942 Test Method for Stability of Cellulose Fibers in Alkaline Environments

D7357 Specification for Cellulose Fibers for Fiber-Reinforced Concrete

D7508/D7508M Specification for Polyolefin Chopped Strands for Use in Concrete

ACI Standards and Reports

Keywords

accuracy; average residual-strength; certification; fibers; fiber-reinforced concrete; flexural parameters; materials for; scales; testing; toughness; Classification; Concrete construction materials/applications--specifications; Concrete reinforcement--specifications; Deterioration resistance; Fiber-reinforced concrete; Field testing--concrete/aggregates; Glass fiber reinforced concrete (GFRC); Polypropylene (PP) fibers; Shotcrete; Steel fiber-reinforced concrete/shotcrete; Synthetic fiber-reinforced concrete/shotcrete; Virgin homopolymer polypropylene fibers ;

ICS Code

ICS Number Code 91.100.30 (Concrete and concrete products)

DOI: 10.1520/C1116_C1116M-08

ASTM International is a member of CrossRef.