ASTM C1193-12
Historical Standard: ASTM C1193-12 Standard Guide for Use of Joint Sealants
SUPERSEDED (see Active link, below)
ASTM C1193
1. Scope
1.1 This guide describes the use of a cold liquid-applied sealant for joint sealing applications. Including joints on buildings and related adjacent areas, such as plazas, decks, and pavements for vehicular or pedestrian use, and types of construction other than highways and airfield pavements and bridges. Information in this guide is primarily applicable to a single and multi-component, cold liquid-applied joint sealant and secondarily to a precured sealant when used with a properly prepared joint opening and substrate surfaces.
1.2 An elastomeric or non-elastomeric sealant described by this guide should meet the requirements of Specification C834 , C920 , or C1311 .
1.3 This guide does not provide information or guidelines for the use of a sealant in a structural sealant glazing application. Guide C1401 should be consulted for this information. Additionally, it also does not provide information or guidelines for the use of a sealant in an insulating glass unit edge seal used in a structural sealant glazing application. Guide C1249 should be consulted for this information.
1.4 Practice C919 should be consulted for information and guidelines for the use of a sealant in an application where an acoustic joint seal is required.
1.5 This guide also does not provide information relative to the numerous types of sealant that are available nor specific generic sealant properties, such as hardness, tack-free time, or curing process, among others.
1.6 The values stated in SI units are to be regarded as the standard. The values given in parenthesis are provided for information only.
1.7 The Committee with jurisdiction for this standard is not aware of any comparable standards published by other organizations.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.
1.9 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C510 Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
C603 Test Method for Extrusion Rate and Application Life of Elastomeric Sealants
C661 Test Method for Indentation Hardness of Elastomeric-Type Sealants by Means of a Durometer
C711 Test Method for Low-Temperature Flexibility and Tenacity of One-Part, Elastomeric, Solvent-Release Type Sealants
C717 Terminology of Building Seals and Sealants
C719 Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
C731 Test Method for Extrudability, After Package Aging, of Latex Sealants
C732 Test Method for Aging Effects of Artificial Weathering on Latex Sealants
C734 Test Method for Low-Temperature Flexibility of Latex Sealants After Artificial Weathering
C792 Test Method for Effects of Heat Aging on Weight Loss, Cracking, and Chalking of Elastomeric Sealants
C793 Test Method for Effects of Laboratory Accelerated Weathering on Elastomeric Joint Sealants
C794 Test Method for Adhesion-in-Peel of Elastomeric Joint Sealants
C834 Specification for Latex Sealants
C919 Practice for Use of Sealants in Acoustical Applications
C920 Specification for Elastomeric Joint Sealants
C1083 Test Method for Water Absorption of Cellular Elastomeric Gaskets and Sealing Materials
C1087 Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
C1135 Test Method for Determining Tensile Adhesion Properties of Structural Sealants
C1184 Specification for Structural Silicone Sealants
C1216 Test Method for Adhesion and Cohesion of One-Part Elastomeric Solvent Release Sealants
C1241 Test Method for Volume Shrinkage of Latex Sealants During Cure
C1247 Test Method for Durability of Sealants Exposed to Continuous Immersion in Liquids
C1248 Test Method for Staining of Porous Substrate by Joint Sealants
C1249 Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
C1253 Test Method for Determining the Outgassing Potential of Sealant Backing
C1257 Test Method for Accelerated Weathering of Solvent-Release-Type Sealants
C1265 Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
C1311 Specification for Solvent Release Sealants
C1330 Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants
C1369 Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
C1382 Test Method for Determining Tensile Adhesion Properties of Sealants When Used in Exterior Insulation and Finish Systems (EIFS) Joints
C1401 Guide for Structural Sealant Glazing
C1442 Practice for Conducting Tests on Sealants Using Artificial Weathering Apparatus
C1472 Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
C1519 Test Method for Evaluating Durability of Building Construction Sealants by Laboratory Accelerated Weathering Procedures
C1521 Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
C1681 Test Method for Evaluating the Tear Resistance of a Sealant Under Constant Strain
D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension
D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D2203 Test Method for Staining from Sealants
D2453 Test Method for Shrinkage and Tenacity of Oil- and Resin-Base Caulking Compounds
Keywords
bond breaker; guide; joint accessories; joint filler; precured sealant, primer; sealant; sealant backing; sealant design; sealant geometry; sealant installation; sealant joint;
ICS Code
ICS Number Code 91.100.50 (Binders. Sealing materials)
DOI: 10.1520/C1193-12
ASTM International is a member of CrossRef.
