1. Scope

1.1 This specification covers cold-weather admixture systems to be added to hydraulic-cement concrete when the temperature of the concrete immediately after placement will be as low as 23.0 F [-5.0 C].

1.2 This specification stipulates tests of the cold-weather admixture system with suitable materials as described in or with materials proposed for specific work (See ). Unless otherwise requested by the purchaser, tests shall be made using suitable concreting materials as described in .

Whenever practicable, tests should be made using the concreting materials, the mixture proportions, and batching sequence proposed for the specific work (See ) because the time of setting, compressive strength gain, and other properties may vary.

1.3 This specification provides three levels of testing.

1.3.1 Level 1During the initial approval stage, proof of compliance with the performance requirements defined in demonstrates that the cold-weather admixture system meets the requirements of this specification. Uniformity and equivalence tests (See Section ) shall be carried out to provide results against which later comparisons can be made.

1.3.2 Level 2Limited retesting is described in , , and . Proof of compliance with the requirements of demonstrates conformity of the admixture system with the requirements of this specification.

1.3.3 Level 3For acceptance of a lot or for measuring uniformity within or between lots, when specified by the purchaser, uniformity and equivalence tests (See Section ) shall be used.

1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.5 The text of this standard references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

The following precautionary caveat pertains to the test methods portion, Sections , of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. WARNING-Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

C33 Specification for Concrete Aggregates

C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens

C125 Terminology Relating to Concrete and Concrete Aggregates

C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates

C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete

C143/C143M Test Method for Slump of Hydraulic-Cement Concrete

C150 Specification for Portland Cement

C157/C157M Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete

C183 Practice for Sampling and the Amount of Testing of Hydraulic Cement

C192/C192M Practice for Making and Curing Concrete Test Specimens in the Laboratory

C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method

C260 Specification for Air-Entraining Admixtures for Concrete

C403/C403M Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance

C494/C494M Specification for Chemical Admixtures for Concrete

C666/C666M Test Method for Resistance of Concrete to Rapid Freezing and Thawing

C1064/C1064M Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete

C1231/C1231M Practice for Use of Unbonded Caps in Determination of Compressive Strength of Hardened Concrete Cylinders

D1193 Specification for Reagent Water

American Concrete Institute Standard

Keywords

chemical admixture; cold-weather admixture; concrete; performance requirements; Chemical admixtures (for concrete); Cold-weather admixture; Cold-weather concrete; Concrete--specifications; Chemical admixtures ;

ICS Code

ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

DOI: 10.1520/C1622_C1622M-05

ASTM International is a member of CrossRef.