|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-C1750 2017ASTM C1750-17Historical Standard: Standard Guide for Development, Verification, Validation, and Documentation of Simulated High-Level Tank WasteASTM C1750Scope 1.1 Intent: 1.1.1 The intent of this guideline is to provide general considerations for the development, verification, validation, and documentation of high-level waste (HLW) tank simulants. Due to the expense and hazards associated with obtaining and working with actual wastes, especially radioactive wastes, simulants are used in a wide variety of applications including process and equipment development and testing, equipment acceptance testing, and plant commissioning. This standard guide facilitates a consistent methodology for development, preparation, verification, validation, and documentation of waste simulants. 1.2 This guideline provides direction on (1) defining simulant use, (2) defining simulant-design requirements, (3) developing a simulant preparation procedure, (4) verifying and validating that the simulant meets design requirements, and (5) documenting simulant-development activities and simulant preparation procedures. 1.3 Applicability: 1.3.1 This guide is intended for persons and organizations tasked with developing HLW simulants to mimic certain characteristics and properties of actual wastes. The process for simulant development, verification, validation, and documentation is shown schematically in Fig. 1. Specific approval requirements for the simulants developed under this guideline are not provided. This topic is left to the performing organization. FIG. 1 Simulant Development, Verification, Validation, and Documentation Flowsheet 1.3.2 While this guide is directed at HLW simulants, much of the guidance may also be applicable to other aqueous based solutions and slurries. 1.3.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 User Caveats: 1.4.1 This guideline is not a substitute for sound chemistry and chemical engineering skills, proven practices and experience. It is not intended to be prescriptive but rather to provide considerations for the development and use of waste simulants. 1.4.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords simulant development; waste simulants; ICS Code ICS Number Code 13.030.30 (Special wastes) DOI: 10.1520/C1750-17 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|