|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-C192 2013ASTM C192 / C192M - 13Standard Practice for Making and Curing Concrete Test Specimens in the LaboratoryActive Standard ASTM C192 / C192M | Developed by Subcommittee: C09.61 Book of Standards Volume: 04.02
Translated Standard: Spanish ASTM C192 / C192MSignificance and Use 3.1 This practice provides standardized requirements for preparation of materials, mixing concrete, and making and curing concrete test specimens under laboratory conditions. 3.2 If specimen preparation is controlled as stipulated herein, the specimens may be used to develop information for the following purposes: 3.2.1 Mixture proportioning for project concrete, 3.2.2 Evaluation of different mixtures and materials, 3.2.3 Correlation with nondestructive tests, and 3.2.4 Providing specimens for research purposes.
Note 1 The concrete test results for concrete specimens made and cured using this practice are widely used.
They may be the basis for acceptance testing for project concrete, research evaluations, and other studies. Careful and knowledgeable handling of materials, mixing concrete, molding test
specimens, and curing test specimens is necessary. Many laboratories performing this important work are independently inspected or accredited. Practice C1077 identifies and defines the
duties, responsibilities, and minimum technical qualification requirements of laboratory personnel and the minimum requirements for equipment used in testing concrete and concrete
aggregates.
1. Scope 1.1 This practice covers procedures for making and curing test specimens of concrete in the laboratory under accurate control of materials and test conditions using concrete that can be consolidated by rodding or vibration as described herein. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ( Warning Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to exposed skin and tissue upon prolonged exposure. 2 )
ASTM Standards C70 Test Method for Surface Moisture in Fine Aggregate C125 Terminology Relating to Concrete and Concrete Aggregates C127 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Coarse Aggregate C128 Test Method for Density, Relative Density (Specific Gravity), and Absorption of Fine Aggregate C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete C143/C143M Test Method for Slump of Hydraulic-Cement Concrete C172 Practice for Sampling Freshly Mixed Concrete C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method C231 Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method C330 Specification for Lightweight Aggregates for Structural Concrete C403/C403M Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance C470/C470M Specification for Molds for Forming Concrete Test Cylinders Vertically C494/C494M Specification for Chemical Admixtures for Concrete C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes C566 Test Method for Total Evaporable Moisture Content of Aggregate by Drying C617 Practice for Capping Cylindrical Concrete Specimens C1064/C1064M Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete C1077 Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation Keywords concrete; cylinders; laboratory; prisms; strength testing ; ICS Code ICS Number Code 91.100.30 (Concrete and concrete products) DOI: 10.1520/C0192_C0192M ASTM International is a member of CrossRef. ASTM C192 / C192MThe following editions for this book are also available...
This book also exists in the following packages...
Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|