1. Scope

1.1 This specification covers external sealing bands to be used in conjunction with concrete pipe as defined in Terminology C 822 and conforming to Specifications C 14M, C 76M, C 412M, C 478M, C 506M, C 507M, C 655M, C 985M, C 1417M, and C 1433M.

1.1.1 Type I, Rubber and Mastic Bands.

1.1.2 Type II, Plastic Film and Mesh Reinforced Mastic Bands.

1.1.3 Type III, Chemically Bonded Adhesive Butyl Bands.

1.2 This specification is the metric counterpart of Specification C 877.

Note 1This specification covers only the design and material of the sealing bands. Sealing bands covered by this specification are adequate, when properly installed, for external hydrostatic pressures up to 90 kPa, (9.14 m) without leakage. The amount of infiltration or exfiltration flow in an installed pipeline is dependent upon many factors other than the sealing bands; allowable quantities and suitable testing of the installed pipeline and system must be covered by other specifications.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip

C14M Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)

C76M Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)

C412M Specification for Concrete Drain Tile (Metric)

C478M Specification for Precast Reinforced Concrete Manhole Sections (Metric)

C506M Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)

C507M Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)

C655M Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)

C681 Test Method for Volatility of Oil- and Resin-Based, Knife-Grade, Channel Glazing Compounds

C766 Test Method for Adhesion After Impact of Preformed Tape Sealants

C822 Terminology Relating to Concrete Pipe and Related Products

C985M Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe (Metric)

C1417M Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)

C1433M Specification for Precast Reinforced Concrete Monolithic Box Sections for Culverts, Storm Drains, and Sewers (Metric)

D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

D217 Test Methods for Cone Penetration of Lubricating Grease

D395 Test Methods for Rubber Property--Compression Set

D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension

D471 Test Method for Rubber Property--Effect of Liquids

D570 Test Method for Water Absorption of Plastics

D573 Test Method for Rubber--Deterioration in an Air Oven

D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers

D882 Test Method for Tensile Properties of Thin Plastic Sheeting

D1171 Test Method for Rubber Deterioration--Surface Ozone Cracking Outdoors or Chamber (Triangular Specimens)

D1278 Test Methods for Rubber from Natural Sources--Chemical Analysis

D1682 Test Method for Breaking Load and Elongation of Textile Fabric

D1963 Test Method for Specific Gravity of Drying Oils, Varnishes, Resins, and Related Materials at 25/25C

D2202 Test Method for Slump of Sealants

D2240 Test Method for Rubber Property--Durometer Hardness

D3407 Test Methods for Joint Sealants, Hot-Poured, for Concrete and Asphalt Pavements

D3953 Specification for Strapping, Flat Steel and Seals

Keywords

bands; external; concrete pipe; joints; Culvert pipe (concrete)--specifications; External sealing bands; Insulating specimens--specifications; Manhole materials/applications--specifications; Precast concrete products--specifications; Sealing bands; Sewer pipe (concrete)--specifications; Storm sewer/drainage concrete pipe--specifications; Concrete pipe--specifications;

ICS Code

ICS Number Code 23.040.80 (Seals for pipe and hose assemblies)

DOI: 10.1520/C0877M-00

ASTM International is a member of CrossRef.