|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D4029 1997ASTM D4029-97Historical Standard: Standard Specification for Finished Woven Glass FabricsASTM D4029Scope 1.1 This specification primarily covers finished fabrics woven from "E" electrical glass fiber yarns that are intended primarily as a reinforcing material in laminated plastics for structural use. This specification can also be applied to fabrics made of glass fiber types as agreed upon between the purchaser and the seller. 1.2 This specification specifies the terminology, definitions, general requirements, and physical requirements for woven glass fiber finished fabrics. This specification permits the application of sizing materials to the glass fiber yarn during manufacture that helps facilitate weaving. When used as permitted in this specification, such materials are compatible with the resin matrix as specified in the contracting instrument. Note 1-Sizing materials on glass fiber yarns, in most cases, are removed by various cleaning procedures as a first stage in preparing a finished fabric. When these yarn sizing materials are removed during a cleaning procedure they need not be compatible with the subsequent resin matrix.1.3 This specification shows the values in both inch-pound units and in SI units. "Inch-pound units" is the technically correct name for the customary units used in the United States. "SI" units is the technically correct name for the system of metric units known as the International System of Units. The values stated in either acceptable metric units or other units shall be regarded separately as standard. The values expressed in each system may not be exact equivalents; therefore each system must be used independently of each other, without combining values in any way. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2-This specification is one of a series to provide a substitute for Military Specifications: MIL-Y-1140H MIL-C-9084C Additional ASTM specifications in this series are currently being drafted and will appear in the Annual Book of ASTM Standards , as available. These are to include greige glass fabrics, glass tapes, glass sleevings, glass yarns, glass cords, glass sewing thread, and finished laminates made from finished glass fabrics. Note 3-Specification D2150, for Woven Glass Fabric for Polyester Glass Laminates, is being extensively revised. This method will contain test methods and requirements for laminated plastics made from fabrics referenced in this specification.Keywords Appearance of materials-textile fabr/fibers; Construction-textile fabr/fibers; Fabric weave; Glass fabr/fibers/textile products-woven glass (for plastic laminates); Laminates-plastic; Organic matter content-textiles; Plast (general)-glass-fiber reinforced products; Plast (general)-textile applications; Twist; Yarn number; Yarns; finished woven glass fabr, spec ICS Code ICS Number Code 59.100.10 (Textile glass materials) DOI: 10.1520/D4029-97 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|