FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D4773 2012ASTM D4773 - 02(2012)Standard Test Method for Purity of Propylene Glycol Monomethyl Ether, Dipropylene Glycol Monomethyl Ether, and Propylene Glycol Monomethyl Ether AcetateActive Standard ASTM D4773 | Developed by Subcommittee: D01.35 Book of Standards Volume: 06.04 ASTM D4773Significance and Use 4.1 This test method is used to determine the purity of PM, DPM, and PMA by subtracting calculated total impurities from 100?%. 4.2 This test method is used to determine the quantity of residual glycol ether present in PMA. 4.3 This test method is used for identifying various impurities in PM, DPM, and PMA. 1. Scope 1.1 This test method covers the determination by gas chromatography of propylene glycol monomethyl ether (PM), dipropylene glycol monomethyl ether (DPM), and propylene glycol monomethyl ether acetate (PMA).
Note 1 Propylene glycol monomethyl ether (PM) is a mixture of two isomers: 1-methoxy-2-propanol and
2-methoxy-1-propanol.
Dipropylene glycol monomethyl ether (DPM) is a mixture of four isomers: 1-(2-methoxy-1-methylethoxy)-2-propanol is one of the major isomers. Propylene glycol monomethyl ether acetate (PMA) is a mixture of two isomers: 1-methoxy-2-acetoxypropane and 2-methoxy-1-acetoxypropane. 1.1.1 This test method covers the determination of PM in the range from 98 to 100?%, and DPM in the range from 0.08 to 0.6?%. 1.1.2 This test method covers the determination of DPM in the range from 98 to 100?%, PM in the range from 0.05 to 0.3?%, and tripropylene glycol monomethyl ether (TPM) in the range from 0.06 to 0.3?%. 1.1.3 This test method covers the determination of PMA in the range from 99 to 100?%, and PM in the range from 0.03 to 1.0?%. 1.2 Water and acid cannot be determined by this test method and must be measured in accordance with Test Methods D1364 and D1613 , and the results used to normalize the chromatographic data. 1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off to the nearest unit in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29 . 1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.5 For hazard information and guidance, see the supplier's Material Safety Data Sheet. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards D1364 Test Method for Water in Volatile Solvents (Karl Fischer Reagent Titration Method) D1613 Test Method for Acidity in Volatile Solvents and Chemical Intermediates Used in Paint, Varnish, Lacquer, and Related Products E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications Keywords dipropylene glycol monomethyl ether; DPM; ether ester; PM; PMA; propylene dipropylene glycol monomethyl ether; propylene glycol monomethyl ether; propylene glycol monomethyl ether acetate; ICS Code ICS Number Code 71.080.60 (Alcohols. Ethers) DOI: 10.1520/D4773-02R12 ASTM International is a member of CrossRef. ASTM D4773This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|