FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D5470 1995ASTM D5470-95Historical Standard: Standard Test Methods for Thermal Transmission Properties of Thin Thermally Conductive Solid Electrical Insulation MaterialsASTM D5470Scope 1.1 This standard covers a test method for measuring thermal impedance of thin electrical insulation materials. 1.2 This test method is useful with either homogeneous or composite thermally conductive sheet material ranging from 0.02 to 10 mm in thickness. 1.3 This test method measures steady-state heat flux through a flat specimen. Calculations are made as if the specimens were homogeneous. In fact, these materials are usually not homogeneous, but the assumption does not detract from the usefulness of the test methods. 1.4 The term "thermal conductivity" applies only to homogeneous materials. Thermally conductive electrical insulating materials are usually heterogeneous since they typically include fillers, binders, reinforcements such as glass fiber mesh, or a layer of polymeric film. To avoid confusion, this test method uses "apparent thermal conductivity" for measurements of both homogeneous and non-homogeneous materials. 1.5 A limitation of using this test method to calculate apparent thermal conductivity is the problem of accurately determining the specimen thickness. To reflect the commercial practice of measuring thickness as manufactured rather than measuring thickness in an assembly, thickness is determined from measurements made at room temperature in accordance with Method C of Test Methods D 374. 1.6 Thermal impedance test data are influenced by contact pressures, specimen surface characteristics, and the existence of alternate paths for heat transmission which are not through the specimen. This test method determines thermal conduction properties under a specific set of conditions (including a 50°C average test temperature) which may not agree exactly with the conditions in an application. As a result, the degree of correlation between this test method and any particular application needs to be determined. 1.7 The values stated in SI units are to be regarded as standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 1—Earlier versions of this document included a Method B (the Roiseland Method). This method is now deleted because of a lack of general support. Keywords apparent thermal conductivity; guarded heater method; MIL-I-49456; thermal conductivity; thermal impedance; thin thermally conductive electrical insulation ICS Code ICS Number Code 29.035.01 (Insulating materials in general) DOI: 10.1520/D5470-95 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|