Significance and Use
The RQD was first introduced in the mid 1960s to provide a simple and inexpensive general indication of rock mass quality to predict tunnelling conditions and support requirements. The
recording of RQD has since become virtually standard practice in drill core logging for a wide variety of geotechnical investigations.
The RQD values provide a basis for making preliminary design decisions involving estimation of required depths of excavation for foundations of structures. The RQD values also can serve to
identify potential problems related to bearing capacity, settlement, erosion, or sliding in rock foundations. The RQD can provide an indication of rock quality in quarries for concrete
aggregate, rockfill, or large riprap.
The RQD has been widely used as a warning indicator of low-quality rock zones that may need greater scrutiny or require additional borings or other investigational work.
The RQD is a basic component of many rock mass classification systems for engineering purposes.
Used alone, RQD is not sufficient to provide an adequate description of rock mass quality. The RQD does not account for joint orientation, tightness, continuity, and gouge material. The RQD
must be used in combination with other geological and geotechnical input.
The RQD is sensitive to the orientation of joint sets with respect to the orientation of the core. That is, a joint set parallel to the core axis will not intersect the core, unless the drill
hole happens to run along the joint. A joint set perpendicular to the core axis will intersect the core axis at intervals equal to the joint spacing. For intermediate orientations, the
spacing of joint intersections with the core will be a cosine function of angle between joints and the core axis.
Core sizes from BQ to PQ with core diameters of 36.5 mm (1.44 in.) and 85 mm (3.35 in.), respectively, are normally acceptable for measuring RQD as long as proper drilling techniques are used
that do not cause excess core breakage or poor recovery, or both. The NX-size (54.7 mm [2.16 in.]) and NQ-size (47.5 mm [1.87 in.]) are the optimal core sizes for measuring RQD. The RQD is
also useful for large core diameters provided the core diameter is clearly stated. The RQD calculated for core smaller than BQ may not be representative of the true quality of the rock mass.
Note 1The quality of the result produced by this standard is dependent on the competence of the personnel performing it, and the suitability of the equipment and
facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing/sampling/inspection/etc. Users of this standard are
cautioned that compliance with Practice D 3740 does not in itself assure reliable results. Reliable results depend on many factors; Practice D 3740 provides a means of evaluating some of
those factors.
1. Scope
1.1 This test method covers the determination of the rock quality designation (RQD) as a standard parameter in drill core logging.
1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026.
1.2.1 The method used to specify how data are collected, calculated, or recorded in this standard is not directly related to the accuracy to which the data can be applied in design or other
uses, or both. How one applies the results obtained using this standard is beyond its scope.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only
and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
D653 Terminology Relating to Soil, Rock, and Contained Fluids
D2113 Practice for Rock Core Drilling and Sampling of Rock for Site Investigation
D3740 Practice for Minimum Requirements for Agencies Engaged in Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
D5079 Practices for Preserving and Transporting Rock Core Samples
D6026 Practice for Using Significant Digits in Geotechnical Data
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
Keywords
classification; index; logging; quality; rock; rock core; Classification; Drilling (in soil/rock); Logging; Rock materials/properties/analysis; RQD (rock quality designation);
ICS Code
ICS Number Code 13.080.99 (Other standards related to soil quality); 73.100.30 (Equipment for drilling and mine excavation)
DOI: 10.1520/D6032-08
ASTM International is a member of CrossRef.
ASTM D6032