ASTM D6254/D6254M-99(2005)
Historical Standard: ASTM D6254/D6254M-99(2005) Standard Specification for Wirebound Pallet-Type Wood Boxes
SUPERSEDED (see Active link, below)
ASTM D6254 / D6254M
1. Scope
1.1 This specification covers the fabrication of new fully enclosed wirebound pallet-type wooden boxes intended for use as containers for domestic and overseas shipment of general materials and supplies, not exceeding 2500 lb [1134 kg] (see 10.1).
1.2 Wirebound pallet-type wooden box performance is dependent on its fabricated components; therefore, a variety of types, classes, and treatments reflecting varied performance are specified. This specification, however, does not cover wirebound pallet-type wooden box performance under all atmosphere, handling, shipping, and storage conditions.
1.3 If the use of other construction methods or techniques is acceptable and permitted (see 5.1.11), the resulting packaging systems shall be of equal or better performance than would result from the use of these specified material and procedures. The appropriate distribution cycle provided in Practice D 4169 can be used to develop comparative procedures and criteria.
1.4 The values stated in either inch-pound or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. See IEEE/ASTM SI 10 for conversion of units.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
American Wood Protection Association (AWPA)
AWPA P36 Standard for Copper Naphthenate (CuN) AWPA P37 Standard for Oxine Copper (Copper-8-Quinolinolate) (Cu8)ASTM Standards
D996 Terminology of Packaging and Distribution Environments
D3951 Practice for Commercial Packaging
D3953 Specification for Strapping, Flat Steel and Seals
D4169 Practice for Performance Testing of Shipping Containers and Systems
D4442 Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
D4444 Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
D6199 Practice for Quality of Wood Members of Containers and Pallets
D6253 Practice for Treatment and/or Marking of Wood Packaging Materials
F1667 Specification for Driven Fasteners: Nails, Spikes, and Staples
IEEE/ASTM SI 10 Standard for Use of the International System of Units (SI): The Modern Metric System
National Institute of Standards and Technology (NIST) Standard
PS 107 Structural Plywood PS 2005 American Softwood Lumber StandardNational Motor Freight Traffic Association
National Motor FreigUniform Classification Committee Standard
Uniform Freight ClasHardwood Plywood and Veneer Association Standard
ANSI/HPVA HP-1-2004 American National Standard for Hardwood and Decorative PlywoodMaterial Handling Industry of America (MHIA)/ANSI Standard
MHIA/ANSI MH1 Pallets, Slip Sheets, and Other Bases for Unit LoadsInternational Standard
International Standa Regulation of Wood Packaging Material in International TradeU.S. Army Research, Development and Engineering Center (ARDEC)
Keywords
blank; box; fasteners; ISPM 15; nails; packaging; pallet; panelboard; shipping container; skid; staples; wire; wirebound; wood;
ICS Code
ICS Number Code 55.160 (Cases. Boxes. Crates)
DOI: 10.1520/D6254_D6254M-99R05
ASTM International is a member of CrossRef.