Cart (0)
  • No items in cart.
Total
$0
There is a technical issue about last added item. You can click "Report to us" button to let us know and we resolve the issue and return back to you or you can continue without last item via click to continue button.
Home
Content
Tour
eLibrary
Store
Search book title
Filters:
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(343)
ACI
(623)
AECDAILY
(599)
AISC
(55)
ASA
(234)
ASCE
(1019)
ASHRAE
(696)
ASME
(2187)
ASSE
(117)
ASTM
(95582)
AWC
(63)
AWWA
(590)
BHMA
(124)
BICSI
(33)
BIFMA
(24)
BOMA
(20)
BSI
(96542)
CRSI
(17)
IAHSS
(1)
IAPMO
(374)
ICC
(325)
IEEE
(7302)
IES
(241)
ISEA
(21)
Joint Commission
(191)
Joint Commission Int.
(1)
NETA
(7)
NFPA
(1669)
TCNA
(18)
TMS
(19)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CO
(1)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(28)
MN
(27)
NC
(30)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(33)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Product - Data Sheet
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Sustainability
 Technical Bulletin
 All
  • ASTM
    D6750-04 Standard Test Methods for Evaluation of Engine Oils in A High-Speed, Single-Cylinder Diesel Engine -1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)
    Edition: 2004
    $144.00
    Unlimited Users per year

Description of ASTM-D6750 2004

ASTM D6750-04

Historical Standard: Standard Test Methods for Evaluation of Engine Oils in A High-Speed, Single-Cylinder Diesel Engine -1K Procedure (0.4 % Fuel Sulfur) and 1N Procedure (0.04 % Fuel Sulfur)




ASTM D6750

Scope

1.1 These test methods cover the performance of engine oils intended for use in certain diesel engines. They are performed in a standardized high-speed, single-cylinder diesel engine by either the 1K (0.4 % fuel sulfur) or 1N (0.04 % fuel sulfur) procedure. The only difference in the two test methods is the fuel used. Piston and ring groove deposit-forming tendency and oil consumption are measured. Also, the piston, the rings, and the liner are examined for distress and the rings for mobility. These test methods are required to evaluate oils intended to satisfy API service categories CF-4 and CH-4 for 1K, and CG-4 for 1N of Specification D 4485.

1.2 These test methods, although based on the original Caterpillar 1K/1N procedures, also embody TMC information letters issued before these test methods were first published. These test methods are subject to frequent change. Until the next revision of these test methods, TMC will update changes in these test methods by the issuance of information letters which shall be obtained from TMC (see ).

1.3 The values stated in inch-pound units or SI units are to be regarded separately as standard. When inch-pound units are standard, the SI units are shown in parenthesis. The values stated in each system are not necessarily exact equivalents. Because of this, combining values from the two systems may be incompatible. Therefore, use either system independently of the other.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given within the text. Being engine tests, these test methods do have definite hazards which shall be met by safe practices (see on Safety).


Keywords

deposits; engine oil; engine wear; 1K test; 1N test; piston-ring-liner scuffing; piston ring sticking; top land heavy carbon


ICS Code

ICS Number Code 75.100 (Lubricants, industrial oils and related products)


DOI: 10.1520/D6750-04



GROUPS
US LOCAL CODES
US Territory Code Adoptions / Amendments
District of Columbia
Guam
Northern Marianas Islands
Puerto Rico
US Virgin Islands
US State Code Adoptions / Amendments
AL AK AZ AR CA CO CT DE
FL GA HI ID IL IN IA KS
KY LA ME MD MA MI MN MS
MO MT NE NV NH NJ NM NY
NC ND OH OK OR PA RI SC
SD TN TX UT VT VA WA WV
WI WY       
X
01 02 03 04 05 06 07 08 09 10
11 12 13 14 15 16 17 18 19 20
21 22 23 24 25 26 27 28 29 30
31 32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49 50
51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69 70
71 72 73 74 75 76 77 78 79 80
81 82 83 84 85 86 87 88 89 90
91 92 93 94 95 96 97 98 99 100