ASTM-D7634, 2010 - MADCAD.com

ASTM D7634 - 10

Standard Test Method for Visualizing Particulate Sizes and Morphology of Particles Contained in Hydrogen Fuel by Microscopy

Active Standard ASTM D7634 | Developed by Subcommittee: D03.14

Book of Standards Volume: 05.06

ASTM D7634

Significance and Use

Low temperature fuel cells such as proton exchange membrane fuel cells (PEMFCs) require high purity hydrogen for maximum material performance and lifetime. The particulates in hydrogen used in FCVs and hydrogen powered internal combustion vehicles may adversely affect pneumatic control components, such as valves or other critical system components. The visualization of the size and morphology of particles is an important tool for determining particle origin as well as for devising particle formation reduction strategies.

1. Scope

1.1 This test method is primarily intended for visualizing and measuring the sizes and morphology of particulates in hydrogen used as a fuel for fuel cell or internal combustion engine powered vehicles. This test method describes procedures required to obtain size and morphology data of known quality. This test method can be applied to other gaseous samples requiring determination of particulate sizes and morphology provided the user s data quality objectives are satisfied.

1.2 Mention of trade names in standard does not constitute endorsement or recommendation. Other manufacturers of equipment, software or equipment models can be used.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

SAE Standards

SAEJ6000 Compressed Hydrogen Surface Vehicle Refueling Connection Devices

ASTM Standards

D7650 Test Method for Test Method for Sampling of Particulate Matter in High Pressure Hydrogen used as a Gaseous Fuel with an In-Stream Filter

Keywords

image; microscope; particulate size;

ICS Code

ICS Number Code 27.075 (Hydrogen technologies)

DOI: 10.1520/D7634-10

ASTM International is a member of CrossRef.

Email *
Password *
Confirm *
First Name *
Last Name *
Title
Company Name *
Company Size *
Industry *
Address *
Address 2
City *
State *	Zip *
Country *
Phone *
How did you hear about MADCAD.com? *

Company*
Full name*
Email*
Phone

Full name*
Email*
Phone
Your selection

MADCAD.com Free Trial

Report To Us

Contact us for a custom quote

⨯To continue with accurate pricing,
please select your company type below:

⨯We need your input!

⨯ We need your input!

⨯We need your input!

⨯We need your input!

Cart Warning

Description of ASTM-D7634 2010

ASTM D7634 - 10

Standard Test Method for Visualizing Particulate Sizes and Morphology of Particles Contained in Hydrogen Fuel by Microscopy

ASTM D7634

ASTM D7634

The following editions for this book are also available...

This book also exists in the following packages...

Subscription Information

About ASTM

Username:
Password:

MADCAD.com Free Trial

Report To Us

Contact us for a custom quote

⨯To continue with accurate pricing, please select your company type below:

⨯We need your input!

⨯ We need your input!

⨯We need your input!

⨯We need your input!

Cart Warning

Description of ASTM-D7634 2010

ASTM D7634 - 10

Standard Test Method for Visualizing Particulate Sizes and Morphology of Particles Contained in Hydrogen Fuel by Microscopy

ASTM D7634

ASTM D7634

⨯To continue with accurate pricing,
please select your company type below: