|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8171 2018ASTM D8171-18Active Standard: Standard Test Methods for Density Determination of Flax FiberASTM D8171Scope 1.1 These test methods cover two procedures for determination of the density of flax fiber and are applicable to fibers of any length. 1.1.1 Test Method A—Gas Pycnometry—This is the more accurate method of density measurement and is preferred in cases in which specimen conditioning (oven drying) can be applied or outgassing effects can be mitigated by purge settings. The level of accuracy for the test methods can be assessed from the precision and bias tables. Outgassing effects can be assessed by performing a purge cycle, pressurization, and pressure stability check on the sample. If the pressure increases in an isolated sample chamber, outgassing may affect the accuracy of results. Oven dry specimens below 55 ºC to equilibrium with a 0 % relative humidity (RH) environment or use longer purge methods, or both, to eliminate outgassing effects. 1.1.2 Test Method B—Buoyancy (Archimedes) Method—This is acceptable as an alternative to Test Method A in applications in which less accurate results are sufficient, as represented in the precision and bias tables. Test Method B is preferred in cases in which outgassing effects in Test Method A cannot be addressed by oven drying or purge settings and prevent Test Method A from producing valid results. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Sections 9 and 17. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords archimedes method; buoyancy method; density; fiber density; flax; natural fibers; pycnometer; pycnometry; ICS Code ICS Number Code 59.060.10 (Natural fibres) DOI: 10.1520/D8171-18 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|