|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8220 2020ASTM D8220-20Active Standard: Standard Guide for Conducting Recall/Removal Procedures for Products in the Cannabis IndustryASTM D8220Scope 1.1 This guide describes the general best-practices action plan for conducting product recall and removal/withdrawal as related to any incident requiring the recovery of cannabis-derived products. This guide applies to all cannabis-derived products commercially manufactured and distributed for consumer use. This guide is for suppliers, consumers, retailers, and distributors. A specific product recall decision is the result of unacceptable product safety and requires notification of the appropriate governmental agencies governing the entity’s product safety laws. Governing regulatory agencies expect a product to be recalled if it is deemed to be unsafe, misbranded, or adulterated. These governing agencies are referenced as regulatory agencies throughout this guide. Various jurisdictional regulatory agencies may have specific and additional recall requirements falling beyond the recommendations of this guide. In these cases, the requirements of the governing regulatory agency must be followed. This document also provides general guidelines for the removal/withdrawal of products from the marketplace. Product removal/withdrawal is undertaken for purely commercial reasons that are typically unrelated to product safety and does not require regulatory agency notification. Product removal/withdrawal is carried out in the same manner as a product recall. This guide is being published as a best-practices approach and does not replace absolute jurisdictional regulatory requirements. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords cannabis; CAPA; CBD; hemp; product recall/removal; product safety; recall/removal procedures; QMS; ICS Code ICS Number Code 11.120.99 (Other standards related to pharmaceutics) DOI: 10.1520/D8220-20 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|