|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8275 2019ASTM D8275-19Historical Standard: Standard Specification for Gasoline-like Test Fuel for Compression-Ignition EnginesASTM D8275Scope 1.1 This specification covers the requirements of test fuels suitable for use in certain gasoline compression-ignition engines and vehicles, which have been specifically designed to operate on the fuel described in this specification. These gasoline-like fuels, which may contain certain gasoline blending components, are henceforth referred to in this specification as “gasoline compression-ignition (GCI) test fuels.” 1.1.1 The GCI test fuels described by this specification are only intended for use by engine and vehicle manufacturers in the continuing development of appropriately designed compression-ignition engines that can take advantage of certain chemical and physical properties of GCI test fuels to achieve higher efficiency and lower emissions (henceforth referred to as “GCI engines”). These GCI test fuels are not intended for use by the general public. 1.1.2 GCI engines include only those engines that directly inject fuel into the combustion chamber, and rely on autoignition of the fuel to initiate combustion part or all the time. Although various combustion strategies may be used depending on the fuel and engine operating condition, the level of fuel stratification is typically decreased in GCI engines under certain operating conditions relative to traditional diesel compression-ignition engines. Engines that use an auxiliary ignition source (such as a spark plug) some but not all of the time could qualify as GCI engines. 1.1.3 The GCI test fuels covered in this specification may contain oxygenates, such as alcohols and ethers. Recommended limits on the type and concentration of specific oxygenates are provided in Appendix X3. 1.2 This specification provides a description of GCI test fuels for automotive engines that are not currently widely available to the general public, but are being developed and require defined standard test fuels. Commercial fuels meeting the same or similar requirements as the GCI test fuels described in this specification could become available to the general public if/when such engines are introduced into commerce; however use of this specification by the general public would require significant modifications. The specification is under continuous review, which can result in revisions based on changes in fuel, automotive requirements, test methods, or a combination thereof. All users of this specification, therefore, should refer to the latest edition. 1.3 Traditional diesel compression-ignition engines and fuel systems are designed for use with fuel, which has a lower volatility, higher flash-point, and higher viscosity than GCI test fuels. Such engines are therefore usually unsuitable for use with GCI test fuels. Certain hardware modifications may be required for the safe use of low flash-point, GCI test fuels. Note 1: If there is any doubt as to the latest edition of Specification D8275, contact ASTM International Headquarters. 1.4 The values stated in SI units are to be regarded as the standard. Any other values given are provided for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords alcohol; automotive fuel; copper strip corrosion; corrosion; distillation; driveability; ethanol; ether; fuel; gasoline; gasoline-alcohol blend; gasoline compression-ignition; gasoline compression-ignition engine fuel; gasoline-ethanol blend; gasoline-ether blend; gasoline-oxygenate blend; induction period; lead; methanol; MTBE; oxidation stability; oxygenate; oxygenate detection; phosphorous; solvent-washed gum; spark-assisted gasoline compression-ignition; sulfur; unleaded fuel; vapor pressure; volatility; ICS Code ICS Number Code 75.160.20 (Liquid fuels) DOI: 10.1520/D8275-19 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|