|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8478 2023ASTM D8478-23Active Standard: Standard Test Method for N-Hexane Recoverable Total Oil and Grease and Total Petroleum Hydrocarbons in Water by ATR-Infrared DeterminationASTM D8478Scope 1.1 This test method covers the determination of total oil and grease, and total petroleum hydrocarbons in produced water and wastewater by an infrared (IR) determination of n-hexane extractable substances from the sample. Included in this estimation of total oil and grease are any other compounds soluble in the n-hexane. 1.2 This test method defines total oil and grease in produced water and wastewater as that which is extractable in the test method and measured by IR absorption from 3.34 µm to 3.54 µm (2825 cm-1 to 2994 cm-1). Similarly, this test method defines total petroleum hydrocarbons in produced water and wastewater as that oil and grease which is not adsorbed by silica gel in the test method, and is measured by IR absorption from 3.34 µm to 3.54 µm (2825 cm-1 to 2994 cm-1). Alternative methods for total oil and grease or total petroleum hydrocarbons, or both, can produce differing results. 1.3 This method covers the range of 5 mg/L to 175 mg/L for total oil and grease and the range of 5 mg/L to 50 mg/L for total petroleum hydrocarbons. The range may be extended to a lower or higher level by extraction of a larger or smaller sample volume collected separately. 1.4 This test method uses horizontal attenuated total reflectance (HATR) with a cubic zirconia crystal. 1.5 This test method is intended as a field test only and should be treated as such. This method is not intended to replace laboratory-based regulatory methods currently in use. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. See Guide D3856 for more information. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords dispersive infrared; filtometric infrared; FTIR; grease; HATR; hexane extraction; oil; spectroscopy; water; ICS Code ICS Number Code 13.060.50 (Examination of water for chemical substances) DOI: 10.1520/D8478-23 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|