Search book title
Enter keywords for book title search
Search book content
Enter keywords for book content search
Filters:
FORMAT
BOOKS
All Books
PACKAGES
All Packages
EDITION
to
PUBLISHER
AABC
(1)
AAMI
(326)
ACI
(572)
AISC
(44)
ASA
(234)
ASCE
(969)
ASHRAE
(652)
ASME
(2114)
ASSE
(64)
ASTM
(92448)
AWC
(54)
AWWA
(535)
BHMA
(117)
BICSI
(33)
BIFMA
(20)
BOMA
(19)
BSI
(92811)
CHD
(3)
CRSI
(17)
IAHSS
(1)
IAPMO
(351)
ICC
(300)
IEEE
(6217)
IES
(239)
ISEA
(16)
Joint Commission
(177)
Joint Commission Int.
(1)
NETA
(5)
NFPA
(1621)
TCNA
(16)
TMS
(18)
USGBC
(28)
WILEY
(4)
 
AR
(6)
AZ
(7)
CA
(115)
CT
(3)
FL
(57)
ID
(5)
IL
(5)
IN
(1)
KY
(1)
LA
(2)
MI
(23)
MN
(26)
NC
(27)
NJ
(13)
NY
(61)
OH
(24)
OR
(22)
PA
(7)
RI
(8)
SC
(20)
SD
(1)
TX
(3)
VA
(50)
VT
(6)
WA
(31)
CONTENT TYPE
 Act
 Admin Code
 Announcements
 Bill
 Book
 CADD File
 CAN
 CEU
 Charter
 Checklist
 City Code
 Code
 Commentary
 Comprehensive Plan
 Conference Paper
 County Code
 Course
 DHS Documents
 Document
 Errata
 Executive Regulation
 Federal Guideline
 Firm Content
 Guideline
 Handbook
 Interpretation
 Journal
 Land Use and Development
 Law
 Legislative Rule
 Local Amendment
 Local Code
 Local Document
 Local Regulation
 Local Standards
 Manual
 Model Code
 Model Standard
 Notice
 Ordinance
 Other
 Paperback
 PASS
 Periodicals
 PIN
 Plan
 Policy
 Product
 Program
 Provisions
 Requirements
 Revisions
 Rules & Regulations
 Standards
 State Amendment
 State Code
 State Manual
 State Plan
 State Standards
 Statute
 Study Guide
 Supplement
 Technical Bulletin
 All
  • ASTM
    D8510/D8510M-23 Standard Test Method for Local Buckling and Crippling under Axial Compressive Loading
    Edition: 2023
    $86.11
    Unlimited Users per year

Description of ASTM-D8510/D8510M 2023

ASTM D8510/D8510M-23

Active Standard: Standard Test Method for Local Buckling and Crippling under Axial Compressive Loading




ASTM D8510/D8510M

Scope

1.1 This test method covers the local buckling and crippling stresses for one-edge-free and no-edge-free cross section configurations using solid laminate composite material construction. Design of test specimens is covered in Guide D8511/D8511M. A number of test parameters may be varied within the scope of the standard, provided that the parameters are fully documented in the test report. The composite material forms are limited to continuous-fiber or discontinuous-fiber (tape, fabric, braids or hybrids of these forms) reinforced composites.

1.2 This test method requires careful specimen design, instrumentation, data measurement and data analysis. The use of this test method requires close coordination between the test requestor and the test lab personnel. Test requestors need to be familiar with Guide D8511/D8511M and CMH-17 Volume 3 Chapter 92 (1).

1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.

1.3.1 Within the text the inch-pound units are shown in brackets.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.


Keywords

composite materials; compression test; crippling; local buckling;


ICS Code

ICS Number Code 59.100.01 (Materials for the reinforcement of composites in general)


DOI: 10.1520/D8510_D8510M-23

This book also exists in the following packages...

Year Publisher Title Annual Price
VAR
ASTM
 [+] $7,461.55 Buy
VAR
ASTM
 [+] $1,144.52 Buy

Subscription Information

MADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

Some features of MADCAD.com ASTM Standards Subscriptions are:

- Online access: With MADCAD.com’ s web based subscription service no downloads or installations are required. Access ASTM Standards from any browser on your computer, tablet or smart phone.

- Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.

 

For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.

 

About ASTM

ASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide.
GROUPS
X