|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D8571 2024ASTM D8571-24Active Standard: Standard Practice for Detection of Hydrocarbon Liquids in Soils by Fluorescence with an Optical Imaging Profiler Using Direct Push MethodsASTM D8571Scope 1.1 This practice presents a method for delineating the subsurface presence of nonaqueous phase liquids (NAPLs) consisting of petroleum hydrocarbons, coal tars, and similar waste materials using an optical image profiler (OIP) system. The OIP probe is advanced into waste materials, soils, and unconsolidated formations using direct push (DP) methods. The OIP system provides data approximately each 15 mm (0.05 ft) of log depth to support high-resolution site characterization. 1.2 OIP logging is limited to wastes, soils, and unconsolidated formations that can be penetrated with the available direct push equipment. The ability to penetrate materials is based on carrying vehicle weight, density of soil/materials, and consistency of soil/materials. Penetration may be limited or damage to sensors or tooling can occur under certain ground conditions. DP tools are not designed to penetrate consolidated rock (Guides D6001/D6001M and D6282/D6282M, Practices D7352 and D8037/D8037M). 1.3 Units—The values stated in SI units are to be regarded as standard, however, inch pound units are indicated for information within parentheses as they are in common use for many users. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.4 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D6026, unless superseded by this standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords CMOS; direct push; fluorescence; groundwater; hydrocarbons; LED; logging; NAPL; OIP; PAH; ultraviolet; ICS Code ICS Number Code 13.030.99 (Other standards related to wastes) DOI: 10.1520/D8571-24 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|