1. Scope

1.1 This specification covers minimum material performance requirements and laboratory test procedures for non-reinforced liquid coating encapsulation products (single or multiple-coat systems) for leaded paint in buildings. The test methods and practices included are listed in Table 1. Specifications for reinforced liquid coating encapsulation products are provided in Specification E1797.

1.2 This specification does not address the selection of an encapsulation product for specific use conditions. Specific use conditions may require performance values other than those stated in this specification. See Guide E1796.

1.3 This specification does not cover the use of encapsulation products on industrial steel structures nor on residential coated metal surfaces because no corrosion control requirements are included.

1.4 This specification applies to any non-reinforced liquid applied product, designed to reduce human exposure to lead in paints, which relies primarily on adhesion for attachment to the surface.

1.5 The laboratory testing specified in this specification shall be performed on the entire non-reinforced liquid coating encapsulation product system, whether single or multiple coat, as applied in the field. A non-reinforced liquid coating encapsulation product shall be comprised of all principal components in the system, including the base and top coats and primer, if specified, for field application. Except for dry abrasion testing, where specialty primers maybe used for flash rust resistance, primers shall not be used solely for product performance testing in accordance with this specification.

1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.7 The results of the test methods included in this specification will not necessarily predict field performance.

1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Federal Test Methods Standard 141D

Federal Test Methods Standard 141C

ASTM Standards

D16 Terminology for Paint, Related Coatings, Materials, and Applications

D522 Test Methods for Mandrel Bend Test of Attached Organic Coatings

D823 Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related Products on Test Panels

D1005 Test Method for Measurement of Dry-Film Thickness of Organic Coatings Using Micrometers

D1212 Test Methods for Measurement of Wet Film Thickness of Organic Coatings

D1308 Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes

D1475 Test Method For Density of Liquid Coatings, Inks, and Related Products

D1653 Test Methods for Water Vapor Transmission of Organic Coating Films

D2370 Test Method for Tensile Properties of Organic Coatings

D2486 Test Methods for Scrub Resistance of Wall Paints

D2794 Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)

D3273 Test Method for Resistance to Growth of Mold on the Surface of Interior Coatings in an Environmental Chamber

D3274 Test Method for Evaluating Degree of Surface Disfigurement of Paint Films by Fungal or Algal Growth, or Soil and Dirt Accumulation

D3359 Test Methods for Measuring Adhesion by Tape Test

D3891 Practice for Preparation of Glass Panels for Testing Paint, Varnish, Lacquer, and Related Products

D3924 Specification for Environment for Conditioning and Testing Paint, Varnish, Lacquer, and Related Materials

D3925 Practice for Sampling Liquid Paints and Related Pigmented Coatings

D3960 Practice for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings

D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser

D4214 Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films

D4414 Practice for Measurement of Wet Film Thickness by Notch Gages

D4708 Practice for Preparation of Uniform Free Films of Organic Coatings

D7091 Practice for Nondestructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive Coatings Applied to Non-Ferrous Metals

E84 Test Method for Surface Burning Characteristics of Building Materials

E1605 Terminology Relating to Lead in Buildings

E1796 Guide for Selection and Use of Liquid Coating Encapsulation Products for Leaded Paint in Buildings

E1797 Specification for Reinforced Liquid Coating Encapsulation Products for Leaded Paint in Buildings

E2239 Practice for Record Keeping and Record Preservation for Lead Hazard Activities

G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

Keywords

abatement; encapsulant; encapsulation; lead; leaded paint; liquid coating; liquid coating encapsulation product; non-reinforced liquid coating encapsulation product;

ICS Code

ICS Number Code 87.040 (Paints and varnishes)

DOI: 10.1520/E1795-00

ASTM International is a member of CrossRef.