|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E2601 2023ASTM E2601-23Active Standard: Standard Practice for Radiological and Nuclear Emergency ResponseASTM E2601Scope 1.1 This practice provides decision-making considerations for response to both accidental and intentional incidents that involve radioactive material. It provides information and guidance for what to include in response planning and what activities to conduct during a response. It also encompasses the practices to respond to any situation complicated by radiation in conjunction with the associated guidance for the specific type of incident. 1.1.1 The intended audience for the standard includes planners as well as emergency responders, incident commanders, and other emergency workers who should be protected from radiation. 1.1.2 The scope of this practice applies to all types of radiological emergencies. While it does not fully consider response to an NPP accident,3 an explosive RDD, or nuclear detonation, detailed guidance to respond to such incidents is provided in other documents, such as those cited in the introduction. With respect to the guidance documents, this practice provides the general principles that apply to the broad range of incidents and associated planning goals but relies on the AHJ to apply and tailor their response planning based on those documents as well as the limitation of the personnel and equipment resources in the jurisdiction. In addition, the AHJ should use those documents to identify improvements to planning and resources to be better prepared for the more complex emergencies. 1.1.3 This practice does not expressly address emergency response to contamination of food or water supplies. 1.1.4 The Emergency Response Guide (ERG) published by the Department of Transportation provides valuable information for response to traffic accidents involving radioactive materials. For other radiological or nuclear incidents, however, the ERG may not provide adequate information on appropriate protective measures and should not be the sole resource used. 1.2 This practice applies to those emergency response agencies that have a role in the response to an accidental or intentional radiological or nuclear incident. It should be used by emergency response organizations such as law enforcement, fire service, emergency medical services, and emergency management. 1.3 This practice assumes that implementation begins with the recognition of a radiological or nuclear incident and ends when emergency response actions cease or the response is supported by specialized regional, state, or federal response assets. 1.4 AHJs using this practice should identify hazards, develop a plan, acquire and track equipment, and provide training consistent with the descriptions provided in Section 6. 1.5 While response to radiological hazards is the focus of this practice, responders must consider all hazards during a response; it is possible that non-radiological hazards may present a greater danger at an incident, particularly in incidents with wide area dispersion. 1.5.1 This practice does not fully address assessing the risks from airborne radioactivity. Equipment to determine this potential hazard is not widely available in emergency responder communities. Like other responses to unknown hazards, respiratory protection commonly used by responders is required until a complete hazard identification assessment is complete. 1.6 This practice is divided into the following sections:
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords emergency response; nuclear; radiation; radiological; ICS Code ICS Number Code 13.200 (Accident and disaster control) DOI: 10.1520/E2601-23 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|