|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E2954 2015ASTM E2954-15Historical Standard: Standard Test Method for Axial Compression Test of Reinforced Plastic and Polymer Matrix Composite Vertical MembersASTM E2954Scope 1.1 This test method covers the evaluation of vertical members in axial compression for “full-sized” specimens with various end conditions with constant cross-sections throughout the length. 1.2 This test method is limited to reinforced plastic and polymer matrix composite materials and covers the determination of the compressive properties of structural members. The method is intended primarily for members of rectangular cross section, but is also applicable to irregularly shaped studs, round posts, or special sections. 1.3 This test method covers short-term axial load testing under standard indoor atmospheric conditions. It does not address: sampling, the ability of the material to carry a sustained long-term load, design load derivations, temperature effects, performance under freeze/thaw or salt spray exposure conditions, chemical/UV exposure effects, or engineering analysis/modeling needed to extrapolate the results to conditions other than those tested. Each of these factors, and potentially others, need to be considered by the design professional or product standard development committee before using the information generated by this test method to assess structural adequacy. 1.4 Short sections are not covered in this test method and should be tested using a material test standard such as Test Method D6108 or Test Methods D198. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords axial compression; polymer matrix composite materials; reinforced plastic; vertical members; ICS Code ICS Number Code 83.140.01 (Rubber and plastic products in general) DOI: 10.1520/E2954-15 The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|