|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-E3236/E3236M 2021ASTM E3236/E3236M-21Active Standard: Standard Specification for Ballistic-resistant Barriers Used in Homeland Security or Public Safety ApplicationsASTM E3236/E3236MScope 1.1 This specification specifies requirements for ballistic-resistant barriers to be used in homeland security or public safety applications for protection against complete penetration of projectiles from small arms2. The purpose of this specification is to define baseline performance for ballistic-resistant barriers. 1.2 Items covered by this specification may be rigid or flexible barriers of uniform ballistic layup that are either temporarily or permanently installed. Examples of products include cubicle partitions; non-structural barriers; security checkpoint barriers; and barriers installed in judges’ benches, school safe rooms, and service counters. 1.2.1 This specification addresses two configurations of barriers: (1) stand-alone and (2) in conjunction. 1.2.2 For barriers that include a viewport(s), each viewport shall be tested in accordance with Test Method E3141/E3141M. 1.2.3 This specification is not intended to address architectural products covered by ASTM Committees F12 and F33, such as building materials and security glazing. 1.3 This specification defines ballistic performance categories, and the supplier shall declare the ballistic performance category(ies) for testing to this specification. 1.4 This specification requires both Resistance to Penetration (RTP) Testing and Ballistic Limit (V50) Testing. 1.4.1 In addition to the required tests, an optional test with specific temperature conditions is provided that allows testing beyond the minimum requirements of this specification. See Appendix X1. Statements of conformance with this specification shall not include any optional tests unless the optional test is conducted, and the results are included in the test report. 1.5 This specification requires testing of ballistic-resistant barriers in one of the following two ways: 1.5.1 Stand-alone Products—Test items shall be shoot packs, armor coupons, or actual products mounted in a test fixture with air backing. 1.5.2 In Conjunction Products—Test items shall be actual products mounted in the intended use configuration, including mounting hardware and any materials expected to be in front of and behind the product. 1.6 It is anticipated that this specification will be referenced by certifiers, purchasers, or other users to meet their specific needs. 1.7 Selection and procurement guidance is provided in Appendix X2 to assist purchasers in using this specification. 1.8 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.8.1 The user of this standard will identify the system of units to be used, and it is critical to ensure that any cross-referenced standards maintain consistency of units between standards. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords ballistic; ballistic barrier; ballistic-resistant barrier; ICS Code ICS Number Code 13.310 (Protection against crime) DOI: 10.1520/E3236_E3236M-21 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|