ASTM E399-06e2
Historical Standard: ASTM E399-06e2 Standard Test Method for Linear-Elastic Plane-Strain Fracture Toughness K Ic of Metallic Materials
SUPERSEDED (see Active link, below)
ASTM E399
1. Scope
1.1 This test method covers the determination of fracture toughness (K Ic ) of metallic materials under predominantly linear-elastic, plane-strain conditions using fatigue precracked specimens having a thickness of 1.6 mm (0.063 in.) or greater subjected to slowly, or in special (elective) cases rapidly, increasing crack-displacement force. Details of test apparatus, specimen configuration, and experimental procedure are given in the Annexes.
Note 1Plane-strain fracture toughness tests of thinner materials that are sufficiently brittle (see ) can be made using other types of specimens () . There is no standard test method for such thin materials.
1.2 This test method is divided into two parts. The first part gives general recommendations and requirements for K Ic testing. The second part consists of Annexes that give specific information on displacement gage and loading fixture design, special requirements for individual specimen configurations, and detailed procedures for fatigue precracking. Additional annexes are provided that give specific procedures for beryllium and rapid-force testing.
1.3 General information and requirements common to all specimen configurations:
SectionReferenced Documents Terminology Stress-Intensity Factor Plane-Strain Fracture Toughness Crack Plane Orientation Summary of Test Method Significance and Use Significance Precautions Practical Applications Apparatus (see also ) Tension Machine Fatigue Machine Loading Fixtures Displacement Gage, Measurement Specimen Size, Configurations, and Preparation (see also ) Specimen Size Estimates Standard and Alternative Specimen Configurations Fatigue Crack Starter Notches Fatigue Precracking (see also ) Crack Extension Beyond Starter Notch General Procedure Specimen Measurements Thickness Width Crack Size Crack Plane Angle Specimen Testing Loading Rate Test Record Calculation and Interpretation of Results Test Record Analysis P m a x /P Q Validity Requirement Specimen Size Validity Requirements Reporting Precision and Bias1.4 Specific requirements related to test apparatus:
Double-Cantilever Displacement Gage Testing Fixtures Bend Specimen Loading Fixture Annex Compact Specimen Loading Clevis Annex1.5 Specific requirements related to individual specimen configurations:
Bend Specimen SE(B)Compact Specimen C(T)Disk-Shaped Compact Specimen DC(T)Arc-Shaped Tension Specimen A(T)Arc-Shaped Bend Specimen A(B)1.6 Specific requirements related to special test procedures:
Fatigue Precracking KIc Specimens Hot-Pressed Beryllium Testing Rapid-Force Testing1.7 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B645 Practice for Linear-Elastic Plane-Strain Fracture Toughness Testing of Aluminum Alloys
B909 Guide for Plane Strain Fracture Toughness Testing of Non-Stress Relieved Aluminum Products
E4 Practices for Force Verification of Testing Machines
E8/E8M Test Methods for Tension Testing of Metallic Materials
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E337 Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
E456 Terminology Relating to Quality and Statistics
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
E1820 Test Method for Measurement of Fracture Toughness
E1823 Terminology Relating to Fatigue and Fracture Testing
E1921 Test Method for Determination of Reference Temperature, To, for Ferritic Steels in the Transition Range
Keywords
Composition analysis--metals/alloys; Cracking--metallic materials; Defects--metals/alloys; Fabricated materials; Failure end point--metals/alloys; Fatigue; Fracture testing--metals/alloys; Loading tests--metals/alloys; Metallurgical materials/applications; Metals and metallic materials; Plane-strain testing; Quality control (QC)--metals; Strain testing--metallic materials; Stress--metallic materials; Tritensile plane strain;
ICS Code
ICS Number Code 77.040.10 (Mechanical testing of metals)
DOI: 10.1520/E0399-06E02
ASTM International is a member of CrossRef.
