|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F1703 2013ASTM F1703 - 13Standard Guide for Skating and Ice Hockey Playing FacilitiesActive Standard ASTM F1703 | Developed by Subcommittee: F08.66 Book of Standards Volume: 15.07 ASTM F17031. Scope 1.1 The intent of this guide is to provide consistent considerations for the design, construction, and retrofitting of ice skating and ice hockey playing facilities. It is intended to establish guidelines that will provide a level of functionality for recreational skating, conformity for the purpose of competition and reduce potential hazards to skaters, players, game officials, spectators, and employees. 1.2 This guide should be taken into consideration by owners/operators, architects, planners, engineers, equipment manufacturers, construction companies, construction contractors, and appropriate inspectors who may be involved in the design and construction of new ice skating/hockey playing facilities. Whenever possible, environmental sustainability and energy efficiency should be taken into consideration in the planning and design of facilities. This guide applies only to the construction and development of new ice skating/hockey playing facilities. Portions, however, may be useful for renovation projects, such as, replacing worn out dasherboards. 1.3 Every arena is unique in material, architecture, and engineering, and therefore will require technical review. This guide is not meant to provide an architectural prototype, but is a guide to set forth measures for the development of safer ice arena venues. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in SI units are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
ASTM Standards A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless A60 Specification for Chromium-Vanadium Steel Bars for Springs; Replaced by A 689, A/t552 A185/A185M Specification for Steel Welded Wire Reinforcement, Plain, for Concrete C150 Specification for Portland Cement C260 Specification for Air-Entraining Admixtures for Concrete C494/C494M Specification for Chemical Admixtures for Concrete C578 Specification for Rigid, Cellular Polystyrene Thermal Insulation D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension D1056 Specification for Flexible Cellular Materials--Sponge or Expanded Rubber D1667 Specification for Flexible Cellular Materials--Poly (Vinyl Chloride) Foam (Closed-Cell) F355 Test Method for Impact Attenuation of Playing Surface Systems and Materials ANSI Standards ANSIZ97.1 Specification for GlassDIN Standards DIN18 036 Hallen fur den EissportOther Standards MIL-STD-810F Environmental Engineering Considerations Laboratory TestsKeywords dasher boards; goal; ice dam; illumination; penalty boxes; player boxes; rink; ICS Code ICS Number Code 97.220.10 (Sports facilities) DOI: 10.1520/F1703-13 ASTM International is a member of CrossRef. ASTM F1703This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|