|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F1920 2015ASTM F1920-15Historical Standard: Standard Test Method for Performance of Rack Conveyor Commercial Dishwashing MachinesASTM F1920Scope 1.1 This test method evaluates the energy and water consumption of rack conveyor, commercial dishwashing machines, hereafter referred to as dishwashers. Dishwashers may have remote or self-contained booster heater. This procedure does not address cleaning or sanitizing performance. 1.2 This test method is applicable to both hot water sanitizing and chemical sanitizing rack conveyor machines, which include both single tank and multiple tank machines. Rackless conveyors (i.e. flight type machines) are included. Dishwasher tank heaters are evaluated separately from the booster heater. Machines designed to be interchangeable in the field from high temp and low temp (i.e. Dual Sanitizing Machines) and vice versa, shall be tested at both settings. Machines should be set for factory settings. If a dishwasher includes a prewash tank heater as an option, energy should be submetered separately for the prewash tank heater. This test method may be used for dishwashers with steam coil tank or booster heat, but not dishwashers with steam injection tank or booster heat. When the test method specifies to use the data plate or manufacturer’s recommendations, instructions, specifications, or requirements, the information source shall be used in the following order of preference and documented in the test report: data plate, user manual, communication with manufacturer. 1.3 The following procedures are included in this test method: 1.3.1 Procedures to Confirm Dishwasher is Operating Properly Prior to Performance Testing: 1.3.1.1 Maximum energy input rate of the tank heaters (10.5). 1.3.1.2 Maximum energy input rate of the booster heater, if applicable (10.6). 1.3.1.3 Final sanitizing rinse water consumption calibration (10.7). 1.3.1.4 Booster temperature calibration, if applicable (10.2). 1.3.1.5 Wash tank temperature calibration (10.3). 1.3.1.6 Wash tank pump and conveyor motor calibration (10.4). 1.3.2 Energy Usage and Cycle Rate Performance Tests: 1.3.2.1 Washing energy performance test (10.8). 1.3.2.2 Tank heater idle energy rate (10.9). 1.3.2.3 Booster idle energy rate, if provided (10.10). 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords booster; conveyor; dishload; dishrack; dishwasher; hot-water sanitizing; tank heater; warewasher; ICS Code ICS Number Code 97.040.01 (Kitchen equipment in general) DOI: 10.1520/F1920-15 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|