|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F1936 2019ASTM F1936-19Redline Standard: Standard Specification for Impact Attenuation of Turf Playing Systems as Measured in the FieldASTM F1936Scope 1.1 This specification establishes an in situ test method and maximum impact attenuation value for all types of turf playing systems and for a number of sport-specific field layouts. It also includes a protocol for determining test point locations on fields that are lined for multiple sports. 1.1.1 Turf playing systems may be located outdoors or indoors, and typically include field areas within the in-bounds lines and areas outside the in-bounds lines extending to sport-specific limit lines; areas where an athlete should expect to encounter impact attenuation performance that complies with this specification. 1.1.2 Site-specific conditions may exist wherein non-turf surface materials, such as track surfacing and/or covers over subsurface structures, are found within the boundaries of the limit lines. These alternate surface materials are not included in the scope of this specification. 1.2 This specification establishes a method for reporting test results and identifying areas within an existing turf playing system where impact attenuation measurements exceed required threshold values. 1.3 Nothing in this specification is intended to impose limitations on what fields can be tested, or how a particular field can be used. Test providers can adapt the procedures and guidelines contained herein to tests performed on any turf playing system. 1.4 This specification does not imply that an impact-related injury cannot be incurred if a turf playing system complies with its g-max performance requirement. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords average g-max; baseball; combination field system; drop test; field hockey; field testing; g-max; impact; impact attenuation; lacrosse; multi-sport; natural grass field system; North American football; shock absorbing; soccer; softball; synthetic turf field system; test point; infill turf system; ICS Code ICS Number Code 97.220.10 (Sports facilities) DOI: 10.1520/F1936-19 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|