BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F2316 2022ASTM F2316-12-Reapproved2022Active Standard: Standard Specification for Airframe Emergency ParachutesASTM F2316Scope 1.1 This specification covers minimum requirements for the design, manufacture, and installation of parachutes for airframes. Airframe emergency parachutes addressed in this specification refer to parachute systems designed, manufactured, and installed to recover the airframe and its occupants at a survivable rate of descent. This specification is not applicable to deep-stall parachutes, spin recovery parachutes, drogue parachutes, or other airframe emergency aerodynamic decelerators not specifically intended for safely lowering the airframe and occupants to the ground. The specification is applicable to these types of parachutes if they are an integral part of an airframe emergency parachute system designed to recover the airframe and occupants at a survivable rate of descent. 1.2 The values stated in SI units are to be regarded as standard. There may be values given in parentheses that are mathematical conversions to inch-pound units. Values in parentheses are provided for information only and are not considered standard. 1.2.1 Note that within the aviation community mixed units are appropriate in accordance with International Civil Aviation Organization (ICAO) agreements. While the values stated in SI units are regarded as standard, certain values such as airspeeds in knots and altitude in feet are also accepted as standard. 1.3 Airframe emergency parachute recovery systems have become an acceptable means of greatly reducing the likelihood of serious injury or death in an in-flight emergency. Even though they have saved hundreds of lives in many different types of conditions, inherent danger of failure, even if properly designed, manufactured and installed, remains due to the countless permutations of random variables (attitude, altitude, accelerations, airspeed, weight, geographic location, etc.) that may exist at time of usage. The combination of these variables may negatively influence the life saving function of these airframe emergency parachute systems. They are designed to be a supplemental safety device and to be used at the discretion of the pilot when deemed to provide the best chance of survivability. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords aircraft; airframe; ballistic recovery; parachute; ICS Code ICS Number Code 49.020 (Aircraft and space vehicles in general) DOI: 10.1520/F2316-12R22 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|