|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3013 2018ASTM F3013-13-Reapproved2018Active Standard: Standard Test Method for Density of Topsoil and Blended Soils In-place by the Core Displacement MethodASTM F3013Scope 1.1 This test method may be used to determine the undisturbed (in-situ) in-place bulk-density, moisture content and unit weight of topsoil and blended soil growing mediums using the Core Displacement Method. 1.2 This test method is applicable for soils without appreciable amounts of rock or coarse material exceeding 1 inch in size. Further it is only suitable for soils in-which the natural void or pore openings in the soil are small enough to prevent the sand used in the test from entering the voids and impacting the test results. Unlike Test Method D1556, this test method is suitable for organic and plastic soils due to the use of a core apparatus, and not hand excavation methods. The material shall have adequate cohesive material or particle attraction to provide a stable core (core hole) for the duration of the test without deforming or sloughing. Therefore this method is not suitable for unbound granular soils that cannot maintain stable sides. This test method is applicable for assessing compaction of surface layers of topsoil (or blended soils) using a soil small core unlike Test Methods D4914, which uses a large volume soil pit excavation. 1.3 This test method is intended for soil typical of growing mediums suitable for sports fields, golf courses and lawn areas that may include organic material, silts, clays and sand. 1.4 This test method is not applicable for soil conditions in-which the root mass is excessive or in-which the root mass includes woody roots. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords core; density; in-place; in-situ; sand; soil; ICS Code ICS Number Code 13.080.20 (Physical properties of soil) DOI: 10.1520/F3013-13R18 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|