|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3363 2019ASTM F3363-19Active Standard: Standard Specification for Unvented Liquid/Gel Fuel-Burning Portable DevicesASTM F3363Scope 1.1 These requirements apply to devices that: 1.1.1 Sustain a flame over the fuel surface in an open reservoir; 1.1.2 Sustain a flame that does not require external ventilation to remove the combustion emissions, and are therefore ventless; 1.1.3 Burn a liquid, gelled, or otherwise non-solid fuel in an open reservoir or from a disposable, non-refillable, fuel container; 1.1.4 Have a fuel capacity of 2.5 L (0.67 gal) or less; 1.1.5 Have a power output of 1.47 kW (5000 BTU/h) or less; 1.1.6 Are intended to be easily carried or moved by hand; and 1.1.7 Are intended for indoor use, outdoor use, or both. 1.2 These requirements do not apply to devices that: 1.2.1 Are candles; 1.2.2 Are intended to cook or warm food; 1.2.3 Burn solid fuels, as determined by the test method described in Test Methods D4359; or 1.2.4 Do not have an open reservoir such as a refillable oil lamp, outdoor garden, or table torch intended to burn combustible fuel using a wick to sustain the flame (see Appendix X1). 1.3 This specification prescribes minimum safety requirements for devices to help ensure a reasonable degree of safety for normal use, thereby improving personal safety and reducing fires, deaths, and injuries. 1.4 This specification is not intended to replace other safety practices such as adult supervision, close monitoring of product when in use, and fire detection, alarm, or suppression systems. 1.5 The values stated in SI units are to be considered standard. The values in parentheses are explanatory or approximate information. 1.6 This specification is used to measure and describe the response of materials, products, or assemblies to heat, flame, and forces under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords carbon monoxide production; combustible liquid fuel; decorative fireplace; ethanol burner; fire pot; fire test; flame mitigation device; flammable liquid fuel; indoor usage test; indoor use; non-refillable canister; oxygen reduction; portable fireplace; stability test; table top fireplace; ICS Code ICS Number Code 97.100.99 (Heaters using other sources of energy) DOI: 10.1520/F3363-19 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|