|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F3568 2023ASTM F3568-23Active Standard: Standard Guide for Medical Qualifications for Suborbital Vehicle PassengersASTM F3568Scope 1.1 This guide provides a consensus set of Space Flight Participant (SFP) acceptance guidelines that will serve as advice to commercial human spaceflight operators as they develop their own medical programs for suborbital flights. 1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 FAA regulatory authority: In 2004 Congress granted the FAA the authority to oversee the safety of the emerging commercial human space flight industry, but limited its rulemaking authority. To ensure the industry had an ample learning period to develop and innovate, Congress prohibited the FAA from issuing any regulations governing the design or operation of a launch vehicle intended to protect the health and safety of crew and space flight participants unless there was a death, serious injury, or close call. The original prohibition expired in 2012, but Congress extended it to 2015, then extended it again to 2016, and finally to October 1, 2023. SFP medical requirements are not under the Amendments Act of 2004 current moratorium that will expire in 2023. The Secretary of the US Department of Transportation (USDOT) has authority to issue regulations regarding SFP medical requirements under Title 51 USC § 50905 (b) (6): (A) The Secretary may issue regulations requiring space flight participants to undergo an appropriate physical examination prior to a launch or reentry under this chapter. This subparagraph shall cease to be in effect three years after the date of enactment of the Commercial Space Launch Amendments Act of 2004. (B) The Secretary may issue additional regulations setting reasonable requirements for space flight participants, including medical and training requirements. Such regulations shall not be effective before the expiration of 3 years after the date of enactment of the Commercial Space Launch Amendments Act of 2004. However, USDOT has declined to exert this authority thus far. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords commercial space flight; medical guidelines; physical and psychological training for spaceflight; SFP; space flight participant; suborbital spaceflight; ICS Code ICS Number Code 49.020 (Aircraft and space vehicles in general) DOI: 10.1520/F3568-23 This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|