|
FORMAT
BOOKS
PACKAGES
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-F391 2002ASTM F391-02Withdrawn Standard: Standard Test Methods for Minority Carrier Diffusion Length in Extrinsic Semiconductors by Measurement of Steady-State Surface Photovoltage (Withdrawn 2003)ASTM F391Scope This standard was transferred to SEMI (www.semi.org) May 2003 1.1 These test methods cover the measurement of minority carrier diffusion lengths in specimens of extrinsic single-crystal semiconducting materials or in homoepitaxial layers of known resistivity deposited on more heavily doped substrates of the same type, provided that the thickness of the specimen or layer is greater than four times the diffusion length. 1.2 These test methods are based on the measurement of surface photovoltage (SPV) as a function of energy (wavelength) of the incident illumination. The following two test methods are described: 1.2.1 Test Method A—Constant magnitude surface photovoltage (CMSPV) method. 1.2.2 Test Method B—Linear photovoltage, constant photon flux (LPVCPF) method. 1.3 Both test methods are nondestructive. 1.4 The limits of applicability with respect to specimen material, resistivity, and carrier lifetime have not been determined; however, measurements have been made on 0.1 to 50 cm n- and p-type silicon specimens with carrier lifetimes as short as 2 ns. 1.5 These test methods were developed for use on single crystal specimens of silicon. They may also be used to measure an effective diffusion length in specimens of other semiconductors such as gallium arsenide (with suitable adjustment of the wavelength (energy) range of the illumination and specimen preparation procedures) and an average effective diffusion length in specimens of polysilicon in which the grain boundaries are normal to the surface. 1.6 These test methods also have been applied to the determination of the width of the denuded zone in silicon wafers. 1.7 These test methods measure diffusion lengths at room temperature (22°C) only. Lifetime and diffusion length are a function of temperature. 1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Keywords diffusion length; minority carriers; polysilicon; silicon; single crystal silicon; surface photovoltag ICS Code ICS Number Code 29.045 (Semiconducting materials) DOI: 10.1520/F0391-02 The following editions for this book are also available...
This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|